- 您現在的位置：買賣IC網 > PDF目錄385265 > CY2SSTV857-27 Clocks and Buffers PDF資料下載
參數資料
| 型號： | CY2SSTV857-27 |
| 英文描述： | Clocks and Buffers |
| 中文描述： | 時鐘和緩沖器 |
| 文件頁數： | 1/2頁 |
| 文件大小： | 36K |
| 代理商： | CY2SSTV857-27 |
ADVANCE
INFORMATION
1.8V, 25-bit (1:1) or 14-bit (1:2)
JEDEC-Compliant Data Register
CY2SSTU32864
Cypress Semiconductor Corporation
Document #: 38-07576 Rev. **
3901 North First Street
San Jose
,
CA 95134
408-943-2600
Revised September 9, 2003
Features
Operating frequency: DC to 333 MHz
Supports DDRII SDRAM
Two operations modes: 25 bit (1:1) and 14 bit (1:2)
1.8V operation
Fully JEDEC-compliant
96-ball LFBGA
Description
All clock and data inputs are compatible with the JEDEC
standard for SSTL_18. The control inputs are LVCMOS. All
outputs are 1.8-V CMOS drivers that have been optimized to
drive the DDR-II DIMM load. The SSTU32864 operates from
a differential clock (CK and CK#). Data are registered at the
crossing of CK going high, and CK# going low.
The C0 input controls the pinout configuration of the 1:2 pinout
from A configuration (when low) to B configuration (when
high). The C1 input controls the pinout configuration from
25-bit 1:1 (when low) to 14-bit 1:2 (when high). C0 = 1 and
C1 = 0 is not allowed and should default to the C0 = C1 = 0
state.
The device monitors both DCS# and CSR# inputs and will gate
the Qn outputs from changing states when both DCS# and
CSR# inputs are high. If either DCS# or CSR# input is low, the
Qn outputs will function normally. The RESET input has priority
over the DCS# and CSR# control and will force the outputs
low. If the DCS#-control functionality is not desired, the CSR#
input can be hardwired to ground, in which case the set-up
time requirement for DCS# would be the same as for the other
D data inputs.
The device supports low-power standby operation. When the
reset input (RESET#) is low, the differential input receivers are
disabled, and undriven (floating) data, clock, and reference
voltage (VREF) inputs are allowed. In addition, when RESET#
is low, all registers are reset and all outputs are forced low. The
LVCMOS RESET# and Cn inputs must always be held at a
valid logic high or low level. To ensure defined outputs from the
register before a stable clock has been supplied, RESET#
must be held in the low state during power-up.
In the DDR-II RDIMM application, RESET# is specified to be
completely asynchronous with respect to CK and CK#.
Therefore, no timing relationship can be guaranteed between
the two. When entering reset, the register will be cleared and
the outputs will be driven low quickly, relative to the time to
disable the differential input receivers. However, when coming
out of reset, the register will become active quickly, relative to
the time to enable the differential input receivers.
Block Diagram
Pin Configuration
相關PDF資料 |
PDF描述 |
|---|---|
| CY2V9950 | Clocks and Buffers |
| CY5057 | Clocks and Buffers |
| CY525A | Stepper Motor Controller/Driver |
| CY545B | Stepper Motor Controller/Driver |
| CZRA4740 | Low Current Operation at 250 ，Low Reverse Leakage,Low Noise Zener Diode |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CY2SSTV857-32 | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Differential Clock Buffer/Driver DDR400/PC3200-Compliant |
| CY2SSTV8575 | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Differential Clock Buffer/Driver |
| CY2SSTV8575AC | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Differential Clock Buffer/Driver |
| CY2SSTV8575ACT | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Differential Clock Buffer/Driver |
| CY2SSTV857LFC-32 | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Differential Clock Buffer/Driver DDR400/PC3200-Compliant |
發布緊急采購，3分鐘左右您將得到回復。