欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: DP83848YB-EVK/NOPB
廠商: National Semiconductor
文件頁數: 25/86頁
文件大小: 0K
描述: EVAL BOARD PHYTER EXTREME TEMP
標準包裝: 1
主要目的: 接口,以太網
已用 IC / 零件: DP83848YB
已供物品:
www.national.com
30
D
P
838
48
YB
4.2.7 Descrambler
A serial descrambler is used to de-scramble the received
NRZ data. The descrambler has to generate an identical
data scrambling sequence (N) in order to recover the origi-
nal unscrambled data (UD) from the scrambled data (SD)
as represented in the equations:
Synchronization of the descrambler to the original scram-
bling sequence (N) is achieved based on the knowledge
that the incoming scrambled data stream consists of
scrambled IDLE data. After the descrambler has recog-
nized 12 consecutive IDLE code-groups, where an
unscrambled IDLE code-group in 5B NRZ is equal to five
consecutive ones (11111), it will synchronize to the receive
data stream and generate unscrambled data in the form of
unaligned 5B code-groups.
In order to maintain synchronization, the descrambler must
continuously monitor the validity of the unscrambled data
that it generates. To ensure this, a line state monitor and a
hold timer are used to constantly monitor the synchroniza-
tion status. Upon synchronization of the descrambler the
hold timer starts a 722
s countdown. Upon detection of
sufficient IDLE code-groups (58 bit times) within the 722
s
period, the hold timer will reset and begin a new count-
down. This monitoring operation will continue indefinitely
given a properly operating network connection with good
signal integrity. If the line state monitor does not recognize
sufficient unscrambled IDLE code-groups within the 722
s
period, the entire descrambler will be forced out of the cur-
rent state of synchronization and reset in order to re-
acquire synchronization.
4.2.8 Code-group Alignment
The code-group alignment module operates on unaligned
5-bit data from the descrambler (or, if the descrambler is
bypassed, directly from the NRZI/NRZ decoder) and con-
verts it into 5B code-group data (5 bits). Code-group align-
ment occurs after the J/K code-group pair is detected.
Once the J/K code-group pair (11000 10001) is detected,
subsequent data is aligned on a fixed boundary.
4.2.9 4B/5B Decoder
The code-group decoder functions as a look up table that
translates incoming 5B code-groups into 4B nibbles. The
code-group decoder first detects the J/K code-group pair
preceded by IDLE code-groups and replaces the J/K with
MAC preamble. Specifically, the J/K 10-bit code-group pair
is replaced by the nibble pair (0101 0101). All subsequent
5B code-groups are converted to the corresponding 4B
nibbles for the duration of the entire packet. This conver-
sion ceases upon the detection of the T/R code-group pair
denoting the End of Stream Delimiter (ESD) or with the
reception of a minimum of two IDLE code-groups.
4.2.10 100BASE-TX Link Integrity Monitor
The 100 Base TX Link monitor ensures that a valid and sta-
ble link is established before enabling both the Transmit
and Receive PCS layer.
Signal detect must be valid for 395us to allow the link mon-
itor to enter the 'Link Up' state, and enable the transmit and
receive functions.
4.2.11 Bad SSD Detection
A Bad Start of Stream Delimiter (Bad SSD) is any transition
from consecutive idle code-groups to non-idle code-groups
which is not prefixed by the code-group pair /J/K.
If this condition is detected, the DP83848YB will assert
RX_ER and present RXD[3:0] = 1110 to the MII for the
cycles that correspond to received 5B code-groups until at
least two IDLE code groups are detected. In addition, the
False Carrier Sense Counter register (FCSCR) will be
incremented by one.
Once at least two IDLE code groups are detected, RX_ER
and CRS become de-asserted.
4.3 10BASE-T TRANSCEIVER MODULE
The 10BASE-T Transceiver Module is IEEE 802.3 compli-
ant. It includes the receiver, transmitter, collision, heart-
beat, loopback, jabber, and link integrity functions, as
defined in the standard. An external filter is not required on
the 10BASE-T interface since this is integrated inside the
DP83848YB. This section focuses on the general 10BASE-
T system level operation.
4.3.1 Operational Modes
The DP83848YB has two basic 10BASE-T operational
modes:
— Half Duplex mode
— Full Duplex mode
Half Duplex Mode
In Half Duplex mode the DP83848YB functions as a stan-
dard IEEE 802.3 10BASE-T transceiver supporting the
CSMA/CD protocol.
Full Duplex Mode
In Full Duplex mode the DP83848YB is capable of simulta-
neously transmitting and receiving without asserting the
collision signal. The DP83848YB's 10 Mb/s ENDEC is
designed to encode and decode simultaneously.
UD
SD
N
()
=
SD
UD
N
()
=
相關PDF資料
PDF描述
200LLE8R2MEFC8X9 CAP ALUM 8.2UF 200V 20% RADIAL
462A423-51-0 BOOT MOLDED
M3DDA-1636J IDC CABLE - MKR16A/MC16G/MKR16A
0210200344 CABLE FLAT FLEX 4" 0.50MM 32POS
UPJ1V390MED1TD CAP ALUM 39UF 35V 20% RADIAL
相關代理商/技術參數
參數描述
DP83848YBX/NOPB 功能描述:以太網 IC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
DP83849C 制造商:NSC 制造商全稱:National Semiconductor 功能描述:PHYTER? DUAL Commercial Temperature Dual Port 10/100 Mb/s Ethernet Physical Layer Transceiver
DP83849C_08 制造商:NSC 制造商全稱:National Semiconductor 功能描述:PHYTER? DUAL Commercial Temperature Dual Port 10/100 Mb/s Ethernet Physical Layer Transceiver
DP83849CVS 功能描述:以太網 IC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
DP83849CVS 制造商:Texas Instruments 功能描述:TRANSCEIVER, ENET PHYTER, DUAL, 80TQFP 制造商:Texas Instruments 功能描述:TRANSCEIVER, ENET PHYTER, DUAL, 80TQFP; Data Rate:100Mbps; Ethernet Type:IEEE 802.3u; Supply Voltage Min:3V; Supply Voltage Max:3.6V; Digital IC Case Style:TQFP; No. of Pins:80; Interface Type:MII, RMII, Serial; Operating Temperature;RoHS Compliant: Yes
主站蜘蛛池模板: 吴忠市| 会东县| 枣庄市| 扎囊县| 蓝山县| 梁平县| 苍溪县| 灵山县| 宜兰县| 宣城市| 靖江市| 花莲县| 南康市| 盱眙县| 保康县| 子洲县| 宁波市| 禹城市| 双城市| 砀山县| 大庆市| 泰来县| 周至县| 锡林郭勒盟| 永城市| 建始县| 乌拉特后旗| 化州市| 宝山区| 崇礼县| 南丰县| 芒康县| 枣庄市| 南靖县| 抚远县| 曲靖市| 南安市| 饶河县| 彭阳县| 城口县| 枝江市|