- 您現在的位置：買賣IC網 > PDF目錄375723 > FAN5018B (Fairchild Semiconductor Corporation) 6-Bit VID Controller 2-4 Phase VR10.X Controller PDF資料下載
參數資料
| 型號： | FAN5018B |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | 6-Bit VID Controller 2-4 Phase VR10.X Controller |
| 中文描述： | 6期西元控制器2-4位的VR10.X控制器 |
| 文件頁數： | 27/30頁 |
| 文件大?。?/td> | 509K |
| 代理商： | FAN5018B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁
PRODUCT SPECIFICATION
FAN501
8
B
REV. 1.0.0 Jul/15/05
27
Figure 10. Transient Setting Waveform
Since the FAN5018B turns off all of the phases (switches
inductors to ground), there is no ripple voltage present
during load release. Thus, you do not have to add headroom
for ripple, allowing your load release V
TRANREL
to be larger
than V
TRAN1
by that amount and still be meeting spec. If
V
TRAN1
and V
TRANREL
are less than the desired final droop,
this implies that capacitors can be removed. When removing
capacitors, check the output ripple voltage as well to ensure
it is still within spec.
Layout and Component Placement
The following guidelines are recommended for optimal
performance of a switching regulator in a PC system.
Key layout issues are illustrated in Figure 11.
Figure 11. Layout Recommendations
General Recommendations
For good results, at least a four-layer PCB is
recommended. This should allow the needed versatility
for control circuitry interconnections with optimal
placement, power planes for ground, input, and output
power, and wide interconnection traces in the rest of the
power delivery current paths. Keep in mind that each
square unit of 1 ounce copper trace has a resistance of
~0.53 m
Ω
at room temperature.
Whenever high currents must be routed between PCB
layers, vias should be used liberally to create several
parallel current paths so that the resistance and inductance
introduced by these current paths is minimized and the via
current rating is not exceeded.
If critical signal lines (including the output voltage sense
lines of the FAN5018B) must cross through power
circuitry, it is best if a signal ground plane can be
interposed between those signal lines and the traces of the
power circuitry to serves as a shield to minimize noise
injection into the signals..
Use an analog ground plane both around and under the
FAN5018B for ground connections to the components
associated with the controller. Tie this plane to the nearest
output decoupling capacitor ground and not to any other
power circuitry to prevent power currents from flowing in
it.
Connect the components around the FAN5018B close to
the controller with short traces. The most important traces
to keep short and away from other traces are the FB and
CSSUM pins.
Connect the output capacitors as close as possible to the
load (or connector) that receives the power (e.g., a
microprocessor core). If the load is distributed, the
capacitors should also be distributed, and generally in
proportion to where the load tends to be more dynamic.
Power Circuitry
Route the switching power path on the PCB to encompass
the shortest possible length in order to minimize radiated
switching noise energy (i.e., EMI) and conduction losses
in the board. Failure to take proper precautions often
results in EMI problems for the entire PC system as well
as noise related operational problems in the power
converter control circuitry. The switching power path is
the loop formed by the current path through the input
capacitors and the power MOSFETs including all
interconnecting PCB traces and planes. The use of short
and wide interconnection traces is especially critical in
this path for two reasons: it minimizes the inductance in
the switching loop, which can cause high-energy ringing,
and it accommodates the high current demand with
minimal voltage loss. Avoid crossing any signal lines over
the switching power path loop, described below.
相關PDF資料 |
PDF描述 |
|---|---|
| FAN5018BMTCX | 6-Bit VID Controller 2-4 Phase VR10.X Controller |
| FAN5019B | 6-Bit VID Controller 2-4 Phase VR10.X Controller |
| FAN5019BMTCX | 6-Bit VID Controller 2-4 Phase VR10.X Controller |
| FAN5019MTC | 6-Bit VID Controller 2-4 Phase VRM10.X Controller |
| FAN5019MTCX | 6-Bit VID Controller 2-4 Phase VRM10.X Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN5018BMTCX | 功能描述:IC CTRLR DC-DC MULTIPH 28TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩(wěn)壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| FAN5019 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:6-Bit VID Controller 2-4 Phase VRM10.X Controller |
| FAN5019_ABC3026B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5019_ABC3116B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5019_BBC3116B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
發(fā)布緊急采購，3分鐘左右您將得到回復。