- 您現在的位置：買賣IC網 > PDF目錄385345 > GS9092A (Gennum Corporation) GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI PDF資料下載
參數資料
| 型號： | GS9092A |
| 廠商： | Gennum Corporation |
| 英文描述： | GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| 中文描述： | GS9092A GenLINX - R的第三270Mb / s的串行SDI和DVB - ASI在內 |
| 文件頁數： | 51/59頁 |
| 文件大小： | 614K |
| 代理商： | GS9092A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁當前第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
GS9092A Data Sheet
34715 - 0
February 2006
51 of 59
3.13.1 Command Word Description
The command word consists of a 16-bit word transmitted MSB first and contains a
read/write bit, an Auto-Increment bit and a 12-bit address.
Figure 3-13
shows the
command word format and bit configurations.
Command words are clocked into the GS9092A on the rising edge of the serial
clock SCLK, which operates in a burst fashion.
When the Auto-Increment bit is set LOW, each command word must be followed
by only one data word to ensure proper operation. If the Auto-Increment bit is set
HIGH, the following data word will be written into the address specified in the
command word, and subsequent data words will be written into incremental
addresses from the previous data word. This facilitates multiple address writes
without sending a command word for each data word.
Auto-Increment may be used for both read and write access.
3.13.2 Data Read and Write Timing
Read and write mode timing for the GSPI interface is shown in
Figure 3-15
and
Figure 3-16
respectively. The timing parameters are defined in
Table 3-13
.
When several devices are connected to the GSPI chain, only one CS must be
asserted during a read sequence.
During the write sequence, all command and following data words input at the
SDIN pin are output at the SDOUT pin as is. Where several devices are connected
to the GSPI chain, data can be written simultaneously to all the devices that have
CS set LOW.
Table 3-13: GSPI Timing Parameters
Parameter
Definition
Specification
t
0
The minimum duration of time chip select, CS, must be
LOW before the first SCLK rising edge.
1.5 ns
t
1
The minimum SCLK period.
18.5 ns
t
2
Duty cycle tolerated by SCLK.
40% to 60%
t
3
Minimum input setup time.
1.5 ns
t
4
Write Cycle: the minimum duration of time between the
last SCLK command (or data word if the Auto-Increment
bit is HIGH) and the first SCLK of the data word.
37.1 ns
t
5
Read Cycle: the minimum duration of time between the
last SCLK command (or data word if the Auto-Increment
bit is HIGH) and the first SCLK of the data word.
148.4 ns
t
5
Read Cycle - ANC_DATA_RDBACK bit HIGH when FIFO
is in ancillary insertion mode (see
Ancillary Data Insertion
on page 29
): the minimum duration of time between the
last SCLK command (or data word if the Auto-Increment
bit is HIGH) and the first SCLK of the data word.
222.6 ns
相關PDF資料 |
PDF描述 |
|---|---|
| GS9092ACNE3 | GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092 | GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092-CNE3 | GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GSC9620 | P-CHANNEL ENHANCEMENT MODE POWER MOSFET |
| GSD2004S-V-GS08 | DIODE 0.225 A, 300 V, 2 ELEMENT, SILICON, SIGNAL DIODE, TO-236AB, ROHS COMPLIANT, PLASTIC PACKAGE-3, Signal Diode |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS9092A_10 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GenLINX III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092ACNE3 | 功能描述:RF, RFID, WIRELESS RoHS:是 類別:集成電路 (IC) >> 接口 - 串行器，解串行器 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 功能:解串器 數據速率:2.5Gbps 輸入類型:串行 輸出類型:并聯 輸入數:- 輸出數:24 電源電壓:1.8 V ~ 3.3 V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP（10x10） 包裝:管件 |
| GS9092ACNTE3 | 制造商:Semtech Corporation 功能描述:270Mb/s Transmitter for SDI & ASI |
| GS9092CNE3 | 制造商:Gennum Corporation 功能描述: |
| GS9092-CNE3 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Gennum Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。