- 您現在的位置：買賣IC網 > PDF目錄385388 > HMP8116 (Intersil Corporation) NTSC/PAL Video Decoder PDF資料下載
參數資料
| 型號： | HMP8116 |
| 廠商： | Intersil Corporation |
| 英文描述： | NTSC/PAL Video Decoder |
| 中文描述： | NTSC / PAL視頻解碼器 |
| 文件頁數： | 21/43頁 |
| 文件大小： | 182K |
| 代理商： | HMP8116 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
21
Host Interface
All internal registers may be written to or read by the host
processor at any time, except for those bits identified as
read-only. The bit descriptions of the control registers are
listed in Tables 8-57.
The HMP8116 supports the fast-mode (up to 400 kbps) I
2
C
interface consisting of the SDA and SCL pins. The device
acts as a slave for receiving and transmitting data over the
serial interface. When the interface is not active, SCL and
SDA must be pulled high using external 4k
pull-up resis-
tors. The slave address for the HMP8116 is 88
H
.
Data is placed on the SDA line when the SCL line is low and
held stable when the SCL line is pulled high. Changing the
state of the SDA line while SCL is high will be interpreted as
either an I
2
C bus START or STOP condition as indicated by
Figure 19.
During I
2
C write cycles, the first data byte after the slave
address is treated as the control register sub address and is
written into the internal address register. Any remaining data
bytes sent during an I
2
C write cycle are written to the control
registers, beginning with the register specified by the
address register as given in the first byte. The address regis-
ter is then autoincremented after each additional data byte
sent on the I
2
C bus during a write cycle. Writes to reserved
bits within registers or reserved registers are ignored.
In order to perform a read from a specific control register
within the HMP8116, an I
2
C bus write must first be per-
formed to properly setup the address register. Then an I
2
C
bus read can be performed to read from the desired control
register(s). As a result of needing the write cycle for a read
cycle there are actually two START conditions as shown in
Figure 20. The address register is then autoincremented
after each byte read during the I
2
C read cycle. Reserved
registers return a value of
00
H
.
FIGURE 18. I
2
C TIMING DIAGRAM
SDA
SCL
t
BUF
t
LOW
t
HIGH
t
R
t
F
t
SU:DATA
t
HD:DATA
t
SU:STOP
SDA
SCL
START
CONDITION
S
1-7
ADDRESS
8
R/W
9
ACK
1-7
DATA
8
9
ACK
STOP
CONDITION
P
FIGURE 19. I
2
C SERIAL DATA FLOW
S = START CYCLE
P = STOP CYCLE
A = ACKNOWLEDGE
NA = NO ACKNOWLEDGE
FROM MASTER
FROM HMP8116
0x88
DATA WRITE
DATA
DATA
0x88
DATA READ
0x89
1000 1000 (R/W)
1000 1000
FIGURE 20. REGISTER WRITE/READ FLOW
S
CHIP ADDR
A
SUB ADDR
DATA
DATA
P
NA
CHIP ADDR
S
SUB ADDR
CHIP ADDR
S
P
A
A
A
A
A
A
REGISTER
POINTED
TO BY
SUB ADDR
OPTIONAL FRAME
MAY BE REPEATED
n TIMES
A
REGISTER
POINTED
TO BY
SUB ADDR
OPTIONAL FRAME
MAY BE REPEATED
n TIMES
HMP8116
相關PDF資料 |
PDF描述 |
|---|---|
| HMP8116CN | NTSC/PAL Video Decoder |
| HMP8117 | NTSC/PAL Video Decoder |
| HMP8117CN | NTSC/PAL Video Decoder |
| HMP8154 | NTSC/PAL Encoders |
| HMP8154CN | NTSC/PAL Encoders |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HMP8116CN | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:NTSC/PAL Video Decoder |
| HMP8117 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:NTSC/PAL Video Decoder |
| HMP8117_07 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:NTSC/PAL Video Decoder |
| HMP8117CN | 功能描述:編碼器、解碼器、復用器和解復用器 80PQFP,0+70C NTSC/PAL VIDEO DECODER W/MA RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray |
| HMP8117CN96 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。