- 您現在的位置：買賣IC網 > PDF目錄360998 > ISP1107 (NXP Semiconductors N.V.) Advanced Universal Serial Bus transceiver PDF資料下載
參數資料
| 型號： | ISP1107 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Advanced Universal Serial Bus transceiver |
| 中文描述： | 先進的通用串行總線收發器 |
| 文件頁數： | 3/19頁 |
| 文件大小： | 536K |
| 代理商： | ISP1107 |
Philips Semiconductors
ISP1107
Advanced USB transceiver
Objective specification
Rev. 01 — 23 February 2000
3 of 19
9397 750 06899
Philips Electronics N.V. 2000. All rights reserved.
6.
Pinning information
6.1 Pinning
6.2 Pin description
Fig 2.
Pinning diagram BCC16
(to be added).
Fig 3.
Pinning diagram TSSOP16.
fpage
ISP1107DH
MGS961
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
Vpu(3.3)
SOFTCON
OE
RCV
VP
VM
SUSPND
GND
VCC(I/O)
SPEED
D
D
+
VO
FSE0
Vreg(3.3)
VCC(5.0)
Table 2:
Symbol
V
pu(3.3)
Pin description
Pin
1
Type
-
Description
pull-up supply voltage (3.3 V
±
10%); used to connect an
external 1.5 k
resistor on D+ (full-speed) or D
(low-speed);
pin function is controlled by input SOFTCON:
SOFTCON = LOW —
V
pu(3.3)
floating (high impedance)
SOFTCON = HIGH —
V
pu(3.3)
= 3.3 V
software controlled USB connection input; a HIGH level
applies 3.3 V to pin V
pu(3.3)
, which is connected to an external
1.5 k
pull-up resistor; this allows USB connect/disconnect
signalling to be controlled by software
output enable input (CMOS level re. V
CC(I/O)
, active LOW);
enables the transceiver to transmit data on the USB bus
differential data receiver output (CMOS level re. V
CC(I/O)
);
driven LOW when input SUSPND is HIGH; the output state of
RCV is preserved and stable during an SE0 condition
single-ended D
+
receiver output (CMOS level re. V
CC(I/O)
);
used for external detection of single-ended zero (SE0), error
conditions, speed of connected device; driven HIGH when
V
CC(5.0)
/V
reg(3.3)
are not connected to any voltage supply
single-ended D
receiver output (CMOS level re. V
CC(I/O)
);
used for external detection of single-ended zero (SE0), error
conditions, speed of connected device; driven HIGH when no
supply voltage is connected to V
CC(5.0)
or V
reg(3.3)
suspend input (CMOS level re. V
CC(I/O)
); a HIGH level enables
low-power state while the USB bus is inactive and drives
output RCV to a LOW level
SOFTCON
2
I
OE
3
I
RCV
4
O
VP
5
O
VM
6
O
SUSPND
7
I
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1107DH | Advanced Universal Serial Bus transceivers |
| ISP1107W | Advanced Universal Serial Bus transceivers |
| ISP1109 | Universal Serial Bus transceiver with carkit support |
| ISP1109BS | Universal Serial Bus transceiver with carkit support |
| ISP1122A | Universal Serial Bus stand-alone hub |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1107DH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Advanced Universal Serial Bus transceiver |
| ISP1107W | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Advanced Universal Serial Bus transceivers |
| ISP1109 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus transceiver with carkit support |
| ISP1109BS | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus transceiver with carkit support |
| ISP1109BS,118 | 功能描述:射頻收發器 USB FS TRANSCVR RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。