- 您現在的位置：買賣IC網 > PDF目錄360998 > ISP1181A (NXP Semiconductors N.V.) Full-speed Universal Serial Bus peripheral controller PDF資料下載
參數資料
| 型號： | ISP1181A |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Full-speed Universal Serial Bus peripheral controller |
| 中文描述： | 全速通用串行總線外設控制器 |
| 文件頁數： | 9/70頁 |
| 文件大小： | 341K |
| 代理商： | ISP1181A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
Philips Semiconductors
ISP1181A
Full-speed USB peripheral controller
Product data
Rev. 05 — 08 December 2004
9 of 70
9397 750 13959
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
7.
Functional description
The ISP1181A is a full-speed USB peripheral controller with up to 14 configurable
endpoints. It has a fast general-purpose parallel interface for communication with
many types of microcontrollers or microprocessors. It supports different bus
configurations (see
Table 3
) and local DMA transfers of up to 16 bytes per cycle. The
block diagram is given in
Figure 1
.
The ISP1181A has 2462 bytes of internal FIFO memory, which is shared among the
enabled USB endpoints. The type and FIFO size of each endpoint can be individually
configured, depending on the required packet size. Isochronous and bulk endpoints
are double-buffered for increased data throughput.
The ISP1181A requires a single supply voltage of 3.3 Vor 5.0 V and has an internal
3.3 V voltage regulator for powering the analog USB transceiver. It supports
bus-powered operation.
The ISP1181A operates on a 6 MHz oscillator frequency. A programmable clock
output is available up to 48 MHz. During ‘suspend’ state the 100 kHz
±
50 %
LazyClock frequency can be output.
7.1 Analog transceiver
The transceiver is compliant with the Universal Serial Bus Specification Rev. 2.0 (full
speed) It interfaces directly with the USB cable through external termination
resistors.
7.2 Philips Serial Interface Engine (SIE)
The Philips SIE implements the full USB protocol layer. It is completely hardwired for
speed and needs no firmware intervention. The functions of this block include:
synchronization pattern recognition, parallel/serial conversion, bit (de-)stuffing, CRC
checking/generation, Packet IDentifier (PID) verification/generation, address
recognition, handshake evaluation/generation.
7.3 Memory Management Unit (MMU) and integrated RAM
The MMU and the integrated RAM provide the conversion between the USB speed
(12 Mbit/s bursts) and the parallel interface to the microcontroller (max. 12 Mbyte/s).
This allows the microcontroller to read and write USB packets at its own speed.
7.4 SoftConnect
The connection to the USB is accomplished by bringing D
+
(for full-speed USB
peripherals) HIGH through a 1.5 k
pull-up resistor. In the ISP1181A, the 1.5 k
pull-up resistor is integrated on-chip and is not connected to V
CC
by default. The
connection is established by a command sent from the external/system
microcontroller. This allows the system microcontroller to complete its initialization
sequence before deciding to establish connection with the USB. Reinitialization of the
USB connection can also be performed without disconnecting the cable.
The ISP1181A will check for USB V
BUS
availability before the connection can be
established. V
BUS
sensing is provided through pin V
BUS
.
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1181ADGG | Full-speed Universal Serial Bus peripheral controller |
| ISP1181B | Full-speed Universal Serial Bus peripheral controller |
| ISP1181BBS | Full-speed Universal Serial Bus peripheral controller |
| ISP1181BDGG | Full-speed Universal Serial Bus peripheral controller |
| ISP1181 | Full-speed Universal Serial Bus Interface Device(全速通用串行總線接口器件) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1181ABS | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Full-speed Universal Serial Bus peripheral controller |
| ISP1181ABS,518 | 功能描述:USB 接口集成電路 USB 1.1 ADV DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1181ABS,551 | 功能描述:USB 接口集成電路 USB 1.1 ADVANCED DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1181ABS,557 | 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1181ABSGE | 功能描述:IC USB CNTRLR FULL-SPD 48-HVQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
發布緊急采購，3分鐘左右您將得到回復。