- 您現在的位置：買賣IC網 > PDF目錄360998 > ISP1181B (NXP Semiconductors N.V.) Full-speed Universal Serial Bus peripheral controller PDF資料下載
參數資料
| 型號： | ISP1181B |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Full-speed Universal Serial Bus peripheral controller |
| 中文描述： | 全速通用串行總線外設控制器 |
| 文件頁數： | 18/70頁 |
| 文件大小： | 341K |
| 代理商： | ISP1181B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
Philips Semiconductors
ISP1181B
Full-speed USB peripheral controller
Product data
Rev. 02 — 07 December 2004
18 of 70
9397 750 13958
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
In DACK-only mode the ISP1181B uses the DACK signal as data strobe. Input
signals RD and WR are ignored. This mode is used in CPU systems that have a
single address space for memory and I/O access. Such systems have no separate
MEMW and MEMR signals: the RD and WR signals are also used as memory data
strobes.
10.4 End-Of-Transfer conditions
10.4.1
Bulk endpoints
A DMA transfer to/from a bulk endpoint can be terminated by any of the following
conditions (bit names refer to the DMA Configuration Register, see
Table 24
):
An external End-Of-Transfer signal occurs on input EOT
The DMA transfer completes as programmed in the DMA Counter register
(CNTREN = 1)
A short packet is received on an enabled OUT endpoint (SHORTP = 1)
DMA operation is disabled by clearing bit DMAEN.
External EOT:
When reading from an OUT endpoint, an external EOT will stop the
DMA operation and
clear any remaining data
in the current FIFO. For a double-
buffered endpoint the other (inactive) buffer is not affected.
When writing to an IN endpoint, an EOT will stop the DMA operation and the data
packet in the FIFO (even if it is smaller than the maximum packet size) will be sent to
the USB host at the next IN token.
DMA Counter Register:
An EOT from the DMA Counter Register is enabled by
setting bit CNTREN in the DMA Configuration Register. The ISP1181B has a 16-bit
DMA Counter Register, which specifies the number of bytes to be transferred. When
DMA is enabled (DMAEN = 1), the internal DMA counter is loaded with the value from
the DMA Counter Register. When the internal counter completes the transfer as
programmed in the DMA counter, an EOT condition is generated and the DMA
operation stops.
Fig 5.
ISP1181B in DACK-only DMA mode.
RAM
ISP1181B
DMA
CONTROLLER
CPU
DREQ
DACK
HRQ
HLDA
HRQ
HLDA
DREQ
DACK
RD
WR
004aaa138
AD0,
DATA1 to DATA15
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1181BBS | Full-speed Universal Serial Bus peripheral controller |
| ISP1181BDGG | Full-speed Universal Serial Bus peripheral controller |
| ISP1181 | Full-speed Universal Serial Bus Interface Device(全速通用串行總線接口器件) |
| ISP1181DGG | INDUCTOR 4.7NH +-.3NH 0402 SMD |
| ISP1183 | Low-power Universal Serial Bus interface device with DMA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1181BBS | 制造商:NXP Semiconductors 功能描述:IC CONTROLLER USB PERIPHERAL SMD 制造商:ST-Ericsson 功能描述:CONTROLLER USB PERIPHERAL 48HVQFN |
| ISP1181BBS,518 | 功能描述:USB 接口集成電路 USB 1.1 DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1181BBS,551 | 功能描述:USB 接口集成電路 USB 1.1 DEVICE CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1181BBS,557 | 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1181BBS518 | 制造商:ST-Ericsson 功能描述:CONTROLLER USB PERIPHERAL 48HVQFN |
發布緊急采購，3分鐘左右您將得到回復。