- 您現在的位置：買賣IC網 > PDF目錄360998 > ISP1181B (NXP Semiconductors N.V.) Full-speed Universal Serial Bus peripheral controller PDF資料下載
參數資料
| 型號： | ISP1181B |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Full-speed Universal Serial Bus peripheral controller |
| 中文描述： | 全速通用串行總線外設控制器 |
| 文件頁數： | 67/70頁 |
| 文件大小： | 341K |
| 代理商： | ISP1181B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁當前第67頁第68頁第69頁第70頁
Philips Semiconductors
ISP1181B
Full-speed USB peripheral controller
Product data
Rev. 02 — 07 December 2004
67 of 70
9397 750 13958
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
[3]
These transparent plastic packages are extremely sensitive to reflow soldering conditions and must
on no account be processed through more than one soldering cycle or subjected to infrared reflow
soldering with peak temperature exceeding 217
°
C
±
10
°
C measured in the atmosphere of the reflow
oven. The package body peak temperature must be kept as low as possible.
These packages are not suitable for wave soldering. On versions with the heatsink on the bottom
side, the solder cannot penetrate between the printed-circuit board and the heatsink. On versions with
the heatsink on the top side, the solder might be deposited on the heatsink surface.
If wave soldering is considered, then the package must be placed at a 45
°
angle to the solder wave
direction. The package footprint must incorporate solder thieves downstream and at the side corners.
Wave soldering is suitable for LQFP, QFP and TQFP packages with a pitch (e) larger than 0.8 mm; it
is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm.
Wave soldering is suitable for SSOP, TSSOP, VSO and VSOP packages with a pitch (e) equal to or
larger than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than
0.5 mm.
Image sensor packages in principle should not be soldered. They are mounted in sockets or delivered
pre-mounted on flex foil. However, the image sensor package can be mounted by the client on a flex
foil by using a hot bar soldering process. The appropriate soldering profile can be provided on
request.
Hot bar soldering or manual soldering is suitable for PMFP packages.
[4]
[5]
[6]
[7]
[8]
[9]
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1181BBS | Full-speed Universal Serial Bus peripheral controller |
| ISP1181BDGG | Full-speed Universal Serial Bus peripheral controller |
| ISP1181 | Full-speed Universal Serial Bus Interface Device(全速通用串行總線接口器件) |
| ISP1181DGG | INDUCTOR 4.7NH +-.3NH 0402 SMD |
| ISP1183 | Low-power Universal Serial Bus interface device with DMA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1181BBS | 制造商:NXP Semiconductors 功能描述:IC CONTROLLER USB PERIPHERAL SMD 制造商:ST-Ericsson 功能描述:CONTROLLER USB PERIPHERAL 48HVQFN |
| ISP1181BBS,518 | 功能描述:USB 接口集成電路 USB 1.1 DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1181BBS,551 | 功能描述:USB 接口集成電路 USB 1.1 DEVICE CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1181BBS,557 | 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1181BBS518 | 制造商:ST-Ericsson 功能描述:CONTROLLER USB PERIPHERAL 48HVQFN |
發布緊急采購，3分鐘左右您將得到回復。