- 您現在的位置：買賣IC網 > PDF目錄360998 > ISP1181B (NXP Semiconductors N.V.) Full-speed Universal Serial Bus peripheral controller PDF資料下載
參數資料
| 型號： | ISP1181B |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Full-speed Universal Serial Bus peripheral controller |
| 中文描述： | 全速通用串行總線外設控制器 |
| 文件頁數： | 36/70頁 |
| 文件大小： | 341K |
| 代理商： | ISP1181B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
Philips Semiconductors
ISP1181B
Full-speed USB peripheral controller
Product data
Rev. 02 — 07 December 2004
36 of 70
9397 750 13958
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
12.2.7
Acknowledge Setup
This command acknowledges to the host that a SETUP packet was received. The
arrival of a SETUP packet disables the Validate Buffer and Clear Buffer commands
for the control IN and OUT endpoints. The microcontroller needs to re-enable these
commands by sending an Acknowledge Setup command, see
Section 9.5
.
Code (Hex): F4 —
acknowledge setup
Transaction —
none
12.3 General commands
12.3.1
Read Endpoint Error Code
This command returns the status of the last transaction of the selected endpoint, as
stored in the Error Code Register. Each new transaction overwrites the previous
status information. The bit allocation of the Error Code Register is shown in
Table 35
.
Code (Hex): A0 to AF —
read error code (control OUT, control IN, endpoint 1 to 14)
Transaction —
read 1 byte
3
OVERWRITE
This bit is set by hardware, a logic 1 indicating that a new Setup
packet has overwritten the previous setup information, before it
was acknowledged or before the endpoint was stalled. This bit is
cleared by reading, if writing the setup data has finished.
Firmware must check this bit before sending an Acknowledge
Setup command or stalling the endpoint. Upon reading a logic 1
the firmware must stop ongoing setup actions and wait for a new
Setup packet.
A logic 1 indicates that the buffer contains a Setup packet.
This bit indicates which buffer is currently selected for CPU
access (0 = primary buffer, 1 = secondary buffer).
reserved
2
1
SETUPT
CPUBUF
0
-
Table 34:
Bit
Endpoint Status Image Register: bit description
…continued
Symbol
Description
Table 35:
Bit
Symbol
Reset
Access
Error Code Register: bit allocation
7
UNREAD
0
R
6
5
4
3
2
1
0
DATA01
0
R
reserved
0
R
ERROR[3:0]
RTOK
0
R
0
R
0
R
0
R
0
R
Table 36:
Bit
7
Error Code Register: bit description
Symbol
Description
UNREAD
A logic 1 indicates that a new event occurred before the
previous status was read.
DATA01
This bit indicates the PID type of the last successfully received
or transmitted packet (0 = DATA0 PID, 1 = DATA1 PID).
6
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1181BBS | Full-speed Universal Serial Bus peripheral controller |
| ISP1181BDGG | Full-speed Universal Serial Bus peripheral controller |
| ISP1181 | Full-speed Universal Serial Bus Interface Device(全速通用串行總線接口器件) |
| ISP1181DGG | INDUCTOR 4.7NH +-.3NH 0402 SMD |
| ISP1183 | Low-power Universal Serial Bus interface device with DMA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1181BBS | 制造商:NXP Semiconductors 功能描述:IC CONTROLLER USB PERIPHERAL SMD 制造商:ST-Ericsson 功能描述:CONTROLLER USB PERIPHERAL 48HVQFN |
| ISP1181BBS,518 | 功能描述:USB 接口集成電路 USB 1.1 DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1181BBS,551 | 功能描述:USB 接口集成電路 USB 1.1 DEVICE CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1181BBS,557 | 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1181BBS518 | 制造商:ST-Ericsson 功能描述:CONTROLLER USB PERIPHERAL 48HVQFN |
發布緊急采購，3分鐘左右您將得到回復。