- 您現在的位置：買賣IC網 > PDF目錄360998 > ISP1181DGG (NXP SEMICONDUCTORS) INDUCTOR 4.7NH +-.3NH 0402 SMD PDF資料下載
參數資料
| 型號： | ISP1181DGG |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 總線控制器 |
| 英文描述： | INDUCTOR 4.7NH +-.3NH 0402 SMD |
| 中文描述： | UNIVERSAL SERIAL BUS CONTROLLER, PDSO48 |
| 封裝： | 6.10 MM, PLASTIC, TSSOP-48 |
| 文件頁數： | 20/69頁 |
| 文件大?。?/td> | 1655K |
| 代理商： | ISP1181DGG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁
Philips Semiconductors
ISP1181
Full-speed USB interface
Objective specification
Rev. 01 — 13 March 2000
20 of 69
9397 750 06896
Philips Electronics N.V. 2000. All rights reserved.
The USB connections D
+
and D
remain powered and logically connected to the
USB bus. If a crystal oscillator is used, powering down during ‘suspend’ is managed
by the internal logic of ISP1181. When using an external oscillator on pin XTAL1, a
stable logic 1 level must be applied during ‘suspend’ state.
Figure 7
shows a typical bus-powered modem application using ISP1181 in
powered-on mode. The SUSPEND output is connected to the reset input (RST) of the
8031 microcontroller via an external inverter. This allows a ‘resume’ condition to wake
up the 8031 from power-down mode. The ISP1181 is woken up via the USB bus
(global resume) or by the ring detection circuit on the telephone line.
11.1.2
Powered-off application
In powered-off application (PWROFF = 1 in the Hardware Configuration Register) the
supply of the CPU and other parts of the circuit is removed during ‘suspend’ state.
The SUSPEND output is active HIGH during ‘suspend’ state, making it suitable as a
power switch control signal, e.g. for an external oscillator.
Input pins of ISP1181 are pulled to ground via the pin buffers. Outputs are made
three-state to prevent current flowing in the application. Bi-directional pins are made
three-state and must be pulled to ground externally by the application. The power
supply of external pull-ups must also be removed to reduce power consumption.
Fig 7.
SUSPEND and WAKEUP signals in a powered-on modem application.
idth
WAKEUP
8031
RST
RING DETECTION
ISP1181
D
+
D
USB
VBUS
VCC(5.0)
VCC
LINE
MGS781
SUSPEND
Fig 8.
Suspend and resume timing for powered-off application.
handbook, full pagewidth
MGS782
WAKEUP
2 ms
0.5 ms
SUSPEND
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1183 | Low-power Universal Serial Bus interface device with DMA |
| ISP1183BS | Low-power Universal Serial Bus interface device with DMA |
| ISP1301 | Universal Serial Bus On-The-Go transceiver |
| ISP1301BS | Universal Serial Bus On-The-Go transceiver |
| ISP1362 | Single-chip Universal Serial Bus On-The-Go controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1183 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low-power Universal Serial Bus interface device with DMA |
| ISP1183BS | 功能描述:IC USB HOST CTRL LOW-SPD 32HVQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| ISP1183BS,118 | 功能描述:USB 接口集成電路 FULL-SPD USB2 DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1183BS,151 | 功能描述:USB 接口集成電路 FULL-SPD USB2 DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1183BS,157 | 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。