- 您現在的位置：買賣IC網 > PDF目錄360999 > ISP1301 (NXP Semiconductors N.V.) Universal Serial Bus On-The-Go transceiver PDF資料下載
參數資料
| 型號： | ISP1301 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Universal Serial Bus On-The-Go transceiver |
| 中文描述： | 通用串行總線在- The - Go的收發器 |
| 文件頁數： | 43/46頁 |
| 文件大小： | 245K |
| 代理商： | ISP1301 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁
Philips Semiconductors
ISP1301
USB OTG transceiver
Product data
Rev. 01 — 14 April 2004
43 of 46
9397 750 11355
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
For packages with leads on two sides and a pitch (e):
–
larger than or equal to 1.27 mm, the footprint longitudinal axis is
preferred
to be
parallel to the transport direction of the printed-circuit board;
–
smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the
transport direction of the printed-circuit board.
The footprint must incorporate solder thieves at the downstream end.
For packages with leads on four sides, the footprint must be placed at a 45
°
angle
to the transport direction of the printed-circuit board. The footprint must
incorporate solder thieves downstream and at the side corners.
During placement and before soldering, the package must be fixed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
Typical dwell time of the leads in the wave ranges from 3 to 4 seconds at 250
°
C or
265
°
C, depending on solder material applied, SnPb or Pb-free respectively.
A mildly-activated flux will eliminate the need for removal of corrosive residues in
most applications.
20.4 Manual soldering
Fix the component by first soldering two diagonally-opposite end leads. Use a low
voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time
must be limited to 10 seconds at up to 300
°
C.
When using a dedicated tool, all other leads can be soldered in one operation within
2 to 5 seconds between 270 and 320
°
C.
20.5 Package related soldering information
[1]
For more detailed information on the BGA packages refer to the (LF)BGA Application Note
(AN01026); order a copy from your Philips Semiconductors sales office.
All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the
maximum temperature (with respect to time) and body size of the package, there is a risk that internal
or external package cracks may occur due to vaporization of the moisture in them (the so called
popcorn effect). For details, refer to the Drypack information in the Data Handbook IC26; Integrated
Circuit Packages; Section: Packing Methods
[2]
Table 52:
Suitability of surface mount IC packages for wave and reflow soldering
methods
Soldering method
Wave
BGA, HTSSON..T
[3]
, LBGA, LFBGA, SQFP,
SSOP..T
[3]
, TFBGA, USON, VFBGA
DHVQFN, HBCC, HBGA, HLQFP, HSO, HSOP,
HSQFP, HSSON, HTQFP, HTSSOP, HVQFN,
HVSON, SMS
PLCC
[5]
, SO, SOJ
LQFP, QFP, TQFP
SSOP, TSSOP, VSO, VSSOP
CWQCCN..L
[8]
, PMFP
[9]
, WQCCN..L
[8]
Package
[1]
Reflow
[2]
suitable
not suitable
not suitable
[4]
suitable
suitable
not recommended
[5][6]
not recommended
[7]
not suitable
suitable
suitable
suitable
not suitable
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1301BS | Universal Serial Bus On-The-Go transceiver |
| ISP1362 | Single-chip Universal Serial Bus On-The-Go controller |
| ISP1362BD | Single-chip Universal Serial Bus On-The-Go controller |
| ISP1362EE | Single-chip Universal Serial Bus On-The-Go controller |
| ISP1501 | Hi-Speed Universal Serial Bus peripheral transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1301BS | 功能描述:IC USB OTG TRANSCEIVER 24-HVQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| ISP1301BS,115 | 功能描述:射頻收發器 USB OTG TRANSCEIVER RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| ISP1301BS,118 | 功能描述:射頻收發器 DO NOT USE ORDER -G OR -S PART RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| ISP1301BS,151 | 功能描述:射頻收發器 USB OTG TRANSCEIVER RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| ISP1301BS,157 | 功能描述:射頻收發器 DO NOT USE ORDER -G OR -S PART RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。