- 您現在的位置：買賣IC網 > PDF目錄360999 > ISP1760 (NXP Semiconductors N.V.) Hi-Speed Universal Serial Bus host controller for embedded applications PDF資料下載
參數資料
| 型號： | ISP1760 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Hi-Speed Universal Serial Bus host controller for embedded applications |
| 中文描述： | 高速嵌入式應用的通用串行總線主控制器 |
| 文件頁數： | 22/105頁 |
| 文件大小： | 449K |
| 代理商： | ISP1760 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁
9397 750 13257
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 01 — 8 November 2004
22 of 105
Philips Semiconductors
ISP1760
Embedded Hi-Speed USB host controller
The PLL block generates all the main internal clocks required for normal functionality of
various blocks: 30 MHz, 48 MHz and 60 MHz.
No external components are required for the PLL operation.
7.6 Power management
The ISP1760 implements a flexible power management scheme, allowing various power
saving stages.
The usual powering scheme implies programming EHCI registers and the internal
Hi-Speed USB (USB 2.0) hub in the same way it is done in the case of a PCI Hi-Speed
USB Host Controller with a Hi-Speed USB hub attached.
When the ISP1760 is in suspend mode, the main internal clocks will be stopped to ensure
minimum power consumption. An internal LazyClock of 100 kHz
±
40 % will continue
running. This allows initiating a resume on one of the following events:
External USB device connect or disconnect
Assertion of the CS_N signal because of any access to the ISP1760
Driving the SUSPEND/WAKEUP_N pin to a LOW level.
The SUSPEND/WAKEUP_N pin is a bidirectional pin. This pin should be connected to
one of the GPIO pins of a processor.
The awake state can be verified by reading the LOW level of this pin. If the level is HIGH,
it means that the ISP1760 is in the suspend state.
The SUSPEND/WAKEUP_N pin requires a pull-up because in the ISP1760 suspended
state the pin becomes three-state and can be pulled down, driving it externally by
switching the processor’s GPIO line to the output mode to generate the ISP1760 wake-up.
The SUSPEND/WAKEUP_N pin is a three-state output. It is also an input to the internal
wake-up logic.
When in suspend mode, the ISP1760 internal wake-up circuitry will sense the status of
the SUSPEND/WAKEUP_N pin:
If it remains pulled-up, no wake-up is generated because a HIGH is sensed by the
internal wake-up circuit.
If the pin is externally pulled LOW (for example, by the GPIO line or just as a test by
jumper), the input to the wake-up circuitry becomes LOW and the wake-up is
internally initiated.
The resume state has a clock-off count timer defined by bits 31 to 16 of the Power Down
Control register. The default value of this timer is 10 ms, meaning that the resume state
will be maintained for 10 ms. If during this time, the RUN/STOP bit in the USBCMD
register is set to logic 1, the Host Controller will go into a permanent resume—the normal
functional state. If the RUN/STOP bit is not set during the time determined by the clock-off
count, the ISP1760 will switch back to suspend mode after the specified time. The
maximum delay that can be programmed in the clock-off count field is approximately
500 ms.
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1761 | Hi-Speed Universal Serial Bus On-The-Go controller |
| ISP1761BE | Hi-Speed Universal Serial Bus On-The-Go controller |
| ISP1761ET | Hi-Speed Universal Serial Bus On-The-Go controller |
| ISP2100A | Telecommunication IC |
| ISP2100BN4 | Microprocessor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1760BE | 制造商:NXP Semiconductors 功能描述:CONTROLLER USB HOST SMD LQFP128 制造商:ST-Ericsson 功能描述:IC CONTROLLER USB HOST 128LQFP |
| ISP1760BE,518 | 功能描述:輸入/輸出控制器接口集成電路 USB HOST CONTROLLER RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| ISP1760BE,551 | 功能描述:輸入/輸出控制器接口集成電路 USB HS HOST CONTRLLR RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| ISP1760BE,557 | 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1760BE518 | 制造商:ST-Ericsson 功能描述:IC CONTROLLER USB HOST 128LQFP |
發布緊急采購，3分鐘左右您將得到回復。