- 您現在的位置：買賣IC網 > PDF目錄30712 > L6219DS-T STEPPER MOTOR CONTROLLER, 1 A, PDSO24 PDF資料下載
參數資料
| 型號： | L6219DS-T |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 1 A, PDSO24 |
| 封裝： | LEAD FREE, MS-013AD, SOIC-24 |
| 文件頁數： | 6/9頁 |
| 文件大小： | 466K |
| 代理商： | L6219DS-T |
Dual Full-Bridge PWM Motor Driver
L6219DS
5
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
Applications Information
PWM Current Control
The L6219DS dual bridge is designed to drive both windings of
a bipolar stepper motor. Output current is sensed and controlled
independently in each bridge by an external sense resistor (RS),
internal comparator, and monostable multivibrator.
When the bridge is turned on, current increases in the motor
winding and it is sensed by the external sense resistor until
the sense voltage (VCOMPIN) reaches the level set at the
comparator’s input:
ITRIP = VREF/10 RS
The comparator then triggers the monostable which turns off
the source driver of the bridge. The actual load current peak
will be slightly higher than the trip point (especially for low-
inductance loads) because of the internal logic and switching
delays. This delay (td) is typically 2 μs. After turn-off, the
motor current decays, circulating through the ground-clamp
diode and sink transistor. The source driver’s off time (and
therefore the magnitude of the current decrease) is determined
by the monostable’s external RC timing components, where
toff = RTCT within the range of 20 kΩ to 100 kΩ and 100 pF to
1000 pF.
The xed-off time should be short enough to keep the current
chopping above the audible range (< 46 μs) and long enough to
properly regulate the current. Because only slow-decay current
control is available, short off times (< 10 μs) require additional
efforts to ensure proper current regulation. Factors that can
negatively affect the ability to properly regulate the current
when using short off times include: higher motor-supply
voltage, light load, and longer than necessary blank time.
When the source driver is re-enabled, the winding current (the
sense voltage) is again allowed to rise to the comparator’s
threshold. This cycle repeats itself, maintaining the average
motor winding current at the desired level.
Loads with high distributed capacitances may result in high
turn-on current peaks. This peak (appearing across RS) will
attempt to trip the comparator, resulting in erroneous current
control or high-frequency oscillations. An external RCCC
time delay should be used to further delay the action of the
comparator. Depending on load type, many applications will
not require these external components (SENSE connected to
COMP IN).
+
–
0
Dwg. W M-003-1A
V PHAS E
I
OUT
td
toff
I TR IP
Dwg. E P -006-1
R S
BB
V
BR IDG E ON
SOUR C E OF F
ALL OF F
PWM Output Current Wave Form
Load Current Paths
相關PDF資料 |
PDF描述 |
|---|---|
| L6382D5TR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| L6382D5 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| L64005-F | SPECIALTY CONSUMER CIRCUIT, PQFP160 |
| L64007 | SPECIALTY CONSUMER CIRCUIT, PQFP160 |
| L64013A1 | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6219DSTR | 功能描述:IC MOTOR DRVR PWM DUAL 24SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 標準包裝:1 系列:- 應用:直流電機驅動器，步進電機驅動器 評估套件:- 輸出數:1 或 2 電流 - 輸出:750mA 電壓 - 負載:10 V ~ 40 V 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-BFSOP（0.295"，7.50mm 寬） 供應商設備封裝:24-SOP 包裝:Digi-Reel® 其它名稱:MTS62C19A-HS105DKR |
| L6219DSTR-T | 功能描述:IC MOTOR DRIVER PWM DUAL 24-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 標準包裝:1 系列:- 應用:直流電機驅動器，步進電機驅動器 評估套件:- 輸出數:1 或 2 電流 - 輸出:750mA 電壓 - 負載:10 V ~ 40 V 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-BFSOP（0.295"，7.50mm 寬） 供應商設備封裝:24-SOP 包裝:Digi-Reel® 其它名稱:MTS62C19A-HS105DKR |
| L6219L-S24-R | 制造商:UTC-IC 制造商全稱:UTC-IC 功能描述:DUAL FULL-BRIDGE PWM MOTOR DRIVER |
| L6219L-S24-T | 制造商:UTC-IC 制造商全稱:UTC-IC 功能描述:DUAL FULL-BRIDGE PWM MOTOR DRIVER |
| L6219R | 功能描述:馬達/運動/點火控制器和驅動器 Dual Stepper Motor RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發(fā)布緊急采購，3分鐘左右您將得到回復。