- 您現在的位置：買賣IC網 > PDF目錄30712 > L6219DS-T STEPPER MOTOR CONTROLLER, 1 A, PDSO24 PDF資料下載
參數資料
| 型號： | L6219DS-T |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 1 A, PDSO24 |
| 封裝： | LEAD FREE, MS-013AD, SOIC-24 |
| 文件頁數： | 7/9頁 |
| 文件大小： | 466K |
| 代理商： | L6219DS-T |
Dual Full-Bridge PWM Motor Driver
L6219DS
6
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
Logic Control of Output Current
Two logic level inputs (I0 and I1) allow digital selection of
the motor winding current at 100%, 67%, 33%, or 0% of the
maximum level per the table below. The 0% output current
condition turns off all drivers in the bridge and can be used as an
OUTPUT ENABLE function.
These logic level inputs greatly enhance the implementation of
μP-controlled drive formats.
During half-step operations, the I0 and I1 allow the μP to control
the motor at a constant torque between all positions in an eight-
step sequence. This is accomplished by digitally selecting 100%
drive current when only one phase is on and 67% drive current
when two phases are on. Logic highs on both I0 and I1 turn off all
drivers to allow rapid current decay when switching phases. This
helps to ensure proper motor operation at high step rates.
The logic control inputs can also be used to select a reduced
current level (and reduced power dissipation) for ‘hold’
conditions and/or increased current (and available torque) for
start-up conditions.
General
The PHASE input to each bridge determines the direction
motor winding current ows. An internally generated dead time
(approximately 2 μs) prevents crossover currents that can occur
when switching the PHASE input.
All four drivers in the bridge output can be turned off between
steps (I0 = I1 ≥ 2.4 V) resulting in a fast current decay through the
internal output clamp and yback diodes. The fast current decay
is desirable in half-step and high-speed applications. The PHASE,
I0,and I1 inputs oat high.
Varying the reference voltage (VREF) provides continuous control
of the peak load current for microstepping applications.
Thermal protection circuitry turns off all drivers when the
junction temperature reaches 170°C. It is only intended to protect
the device from failures due to excessive junction temperature
and should not imply that output short circuits are permitted. The
output drivers are re-enabled when the junction temperature cools
to 145°C.
The L6219DS output drivers are optimized for low output
saturation voltages—less than 1.8 V total (source plus sink) at
500 mA. Under normal operating conditions, when combined
with the excellent thermal properties of the fused internal lead
package design, this allows continuous operation of both bridges
simultaneously at 500 mA.
Current-Control Truth Table
l0
I1
Output Current
LL
VREF/10 RS = ITRIP
HL
VREF/15 RS = 2/3 ITRIP
LH
VREF/30 RS = 1/3 ITRIP
HH
0
相關PDF資料 |
PDF描述 |
|---|---|
| L6382D5TR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| L6382D5 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| L64005-F | SPECIALTY CONSUMER CIRCUIT, PQFP160 |
| L64007 | SPECIALTY CONSUMER CIRCUIT, PQFP160 |
| L64013A1 | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6219DSTR | 功能描述:IC MOTOR DRVR PWM DUAL 24SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 標準包裝:1 系列:- 應用:直流電機驅動器，步進電機驅動器 評估套件:- 輸出數:1 或 2 電流 - 輸出:750mA 電壓 - 負載:10 V ~ 40 V 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-BFSOP（0.295"，7.50mm 寬） 供應商設備封裝:24-SOP 包裝:Digi-Reel® 其它名稱:MTS62C19A-HS105DKR |
| L6219DSTR-T | 功能描述:IC MOTOR DRIVER PWM DUAL 24-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 標準包裝:1 系列:- 應用:直流電機驅動器，步進電機驅動器 評估套件:- 輸出數:1 或 2 電流 - 輸出:750mA 電壓 - 負載:10 V ~ 40 V 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-BFSOP（0.295"，7.50mm 寬） 供應商設備封裝:24-SOP 包裝:Digi-Reel® 其它名稱:MTS62C19A-HS105DKR |
| L6219L-S24-R | 制造商:UTC-IC 制造商全稱:UTC-IC 功能描述:DUAL FULL-BRIDGE PWM MOTOR DRIVER |
| L6219L-S24-T | 制造商:UTC-IC 制造商全稱:UTC-IC 功能描述:DUAL FULL-BRIDGE PWM MOTOR DRIVER |
| L6219R | 功能描述:馬達/運動/點火控制器和驅動器 Dual Stepper Motor RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。