- 您現在的位置：買賣IC網 > PDF目錄30713 > L9949TR (STMICROELECTRONICS) BRUSH DC MOTOR CONTROLLER, 10 A, PDSO20 PDF資料下載
參數資料
| 型號： | L9949TR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSH DC MOTOR CONTROLLER, 10 A, PDSO20 |
| 封裝： | POWER, SO-20 |
| 文件頁數： | 6/22頁 |
| 文件大小： | 418K |
| 代理商： | L9949TR |
L9949
14/20
SPI Interface – Input Data and Status Register
Input Data Register
Status Register
BIT
Function
BIT
Function
Register 0
Register 1
15
High level reset all bits in selected status
register
15
always H
14
VS under- / overvoltage lockout bit
14
VS overvoltage
not used
– set to L
13
12
Control bits for standby mode and
Current monitor multiplexer
13
VS undervoltage
chargepump off
bit13
bit12
function
12
Temperature
shutdown
Temperature
warning
0
standby mode
11
OUT6 – HS driver
overcurrent
OUT6 – HS driver
open load
01
OUT1
1
0
OUT2
10
OUT5 – HS driver
overcurrent
OUT5 – HS driver
open load
11
OUT6
11
OUT6 – HS driver on/off (1)
(1)
If the bits of HS- and LS-driver of the same output stage are high, the internal logic prevents that both drivers of this output stage can
be switched on simultaneously in order to avoid a high internal current from VS to GND.
9
OUT5 – LS driver
overcurrent
OUT5 – LS driver
open load
10
OUT5 – HS driver on/off (1)
8
OUT4 – HS driver
overcurrent
OUT4 – HS driver
open load
9
OUT5 – LS driver on/off (1)
7
OUT4 – LS driver
overcurrent
OUT4 – LS driver
open load
8
OUT4 – HS driver
on/off 5(1)
test mode
6
OUT3 – HS driver
overcurrent
OUT3 – HS driver
open load
bit 8
bit 7
7
OUT4 – LS driver
on/off 5(1)
1
5
OUT3 – LS driver
overcurrent
OUT3 – LS driver
open load
B-driver is active
6
OUT3 – HS driver
on/off 5(1)
test mode
4
OUT2 – HS driver
overcurrent
OUT2 – HS driver
open load
bit 6
bit 5
5
OUT3 – LS driver
on/off 5(1)
1
3
OUT2 – LS driver
overcurrent
OUT2 – LS driver
open load
A-driver is active
4
OUT2 – HS driver on/off 51
2
OUT1 – HS driver
overcurrent
OUT1 – HS driver
open load
3
OUT2 – LS driver on/off 1
1
OUT1 – LS driver
overcurrent
OUT1 – LS driver
open load
2
OUT1 – HS driver on/off 1
0
no fault condition (2)
(2)
A logical NOR-combination of all bits 1 to 14 in both status registers. This bit can be polled by the micro-controller without the need
of the full SPI communication (see Figure 13). A broken VCC-connection of the L9949 can be detected by the microcontroller, bec ause
all 15 bits low or high is not a valid frame.
1
OUT1 – LS driver on/off 1
H = on; L = off; HS = highside; LS = lowside
0
Status register select bit
L: status register 0; H: status register 1
相關PDF資料 |
PDF描述 |
|---|---|
| L9950XPTR | BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36 |
| L9950 | BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36 |
| L9950TR | BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36 |
| L9953XPTR | BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36 |
| L9953TR | BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9950 | 功能描述:馬達/運動/點火控制器和驅動器 DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9950_09 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Door actuator driver |
| L9950TR | 功能描述:馬達/運動/點火控制器和驅動器 DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9950XP | 功能描述:馬達/運動/點火控制器和驅動器 DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9950XPTR | 功能描述:馬達/運動/點火控制器和驅動器 DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。