- 您現在的位置：買賣IC網 > PDF目錄361025 > LM2743 (National Semiconductor Corporation) N-Channel FET Synchronous Buck Regulator Controller for Conversion from 3.3V PDF資料下載
參數資料
| 型號： | LM2743 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | N-Channel FET Synchronous Buck Regulator Controller for Conversion from 3.3V |
| 中文描述： | N溝道場效應管同步降壓穩壓控制器，用于從3.3V轉換 |
| 文件頁數： | 2/23頁 |
| 文件大小： | 653K |
| 代理商： | LM2743 |
Connection Diagram
20095202
14-Lead Plastic TSSOP
θ
JA
= 155C/W
NS Package Number MTC14
Pin Description
BOOT (Pin 1)
- Supply rail for the N-channel MOSFET gate
drive. The voltage should be at least one gate threshold
(V
) above the regulator input voltage (V
IN
) to properly
turn on the high-side FET.
LG (Pin 2)
- Gate drive for the low-side N-channel MOSFET.
This signal is interlocked with HG (Pin 14) to avoid a shoot-
through problem.
PGND (Pins 3, 13)
- Ground for low-side FET drive circuitry.
Connect to system ground.
SGND (Pin 4)
- Ground for signal level circuitry. Connect to
system ground.
V
CC
(Pin 5)
Supply rail for the controller.
PWGD (Pin 6)
- Power good pin. This is an open drain
output. The pin is pulled low when the chip is in under-
voltage flag (UVF), over-voltage flag (OVF), or UVLO mode.
During normal operation, this pin is connected to V
CC
or
other low voltage source through a pull-up resistor (R
PULL-
UP
).
I
(Pin 7)
- Current limit threshold setting. This sources a
fixed 40μA current. A resistor of appropriate value should be
connected between this pin and the drain of the low-side
FET.
EAO (Pin 8)
- Output of the error amplifier. The voltage level
on this pin is compared with an internally generated ramp
signal to determine the duty cycle. This pin is necessary for
compensating the control loop.
SS (Pin 9)
- Soft start and track pin. A 10 μA current is
sourced from this pin. This pin is connected to the non-
inverting input of the error amplifier during soft start, or any
time the voltage is below the reference. To track power
supplies connect a resistor divider (smaller than 10k
for
better precision) from the output of the master supply directly
to the SS pin. To limit the inrush current of a single power
supply, place a capacitor to ground (see Application
Information/Start Up for appropriate capacitance value). This
pin should not be forced before SD or V
CC
(above the
UVLO).
FB (Pin 10)
- This is the inverting input of the error amplifier,
which is used for sensing the output voltage and compen-
sating the control loop. The FB current is negligible.
FREQ (Pin 11)
- The switching frequency (F
) is set by
connecting a resistor (R
FADJ
) between this pin and ground.
SD (Pin 12)
- IC shutdown pin. To assure proper IC start-up
the SD pin should not be left floating. When this pin is pulled
low the chip turns both, high and low, sides off. While this pin
is low, the IC will not start up. This pin features a precision
threshold for power supply sequencing, as well as a lower
threshold to ensure minimal quiescent current.
HG (Pin 14)
- Gate drive for the high-side N-channel MOS-
FET. This signal is interlocked with LG (Pin 2) to avoid a
shoot-through problem.
L
www.national.com
2
相關PDF資料 |
PDF描述 |
|---|---|
| LM2744 | Low Voltage N-Channel MOSFET Synchronous Buck Regulator Controller with External Reference |
| LM2796TL | Dual-Display White LED Driver with 3/2x Switched Capacitor Boost |
| LM2796TLX | Dual-Display White LED Driver with 3/2x Switched Capacitor Boost |
| LM2796 | Dual-Display White LED Driver with 3/2x Switched Capacitor Boost |
| LM2925 | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2743-19AEVAL | 功能描述:電源管理IC開發工具 LM2743 EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| LM2743EVAL | 功能描述:BOARD EVALUATION LM2743 RoHS:否 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:PowerWise® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| LM2743EVAL/NOPB | 功能描述:電源管理IC開發工具 LM2743 EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| LM2743MTC | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| LM2743MTC/NOPB | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。