欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: LTC3541EDD#TRPBF
廠商: Linear Technology
文件頁數: 12/20頁
文件大小: 368K
描述: IC REG DL BCK/LINEAR SYNC 10-DFN
產品培訓模塊: More Information on LDOs
標準包裝: 2,500
拓撲: 降壓(降壓)同步(1),線性(LDO)(1)
功能: 任何功能
輸出數: 2
頻率 - 開關: 2.25MHz
電壓/電流 - 輸出 1: 0.8 V ~ 5 V,500mA
電壓/電流 - 輸出 2: 0.4 V ~ 4.1 V,300mA
帶 LED 驅動器:
帶監控器:
帶序列發生器:
電源電壓: 0.9 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 10-WFDFN 裸露焊盤
供應商設備封裝: 10-DFN(3x3)
包裝: 帶卷 (TR)
LTC3541

3541fa
PPLICATIO S I FOR ATIO
U
U
be obtained by choosing an output capacitor value of 10礔
to 22礔. Typically, once the ESR requirement for C
OUT
has
been met, the RMS current rating generally far exceeds
the I
RIPPLE(P-P)
requirement. The output ripple 擵
OUT
is
determined by:
E?nbsp   +
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
V   I ESR
fc
OUT   L
OUT
1
8
where f = operating frequency, C
OUT
= output capacitance
and 擨
L
= ripple current in the inductor. For a fixed output
voltage, the output ripple is highest at maximum input
voltage since 擨
L
increases with input voltage.
Aluminum electrolytic and dry tantalum capacitors are both
available in surface mount configurations. In the case of
tantalum, it is critical that the capacitors are surge tested
for use in switching power supplies. An excellent choice is
the AVX TPS series of surface mount tantalum. These are
specially constructed and tested for low ESR so they give
the lowest ESR for a given volume. Other capacitor types
include Sanyo POSCAP, Kemet T510 and T495 series, and
Sprague 593D and 595D series. Consult the manufacturer
for other specific recommendations.
Using Ceramic Input and Output Capacitors
High value, low cost ceramic capacitors are now becoming
available in smaller case sizes. Their high ripple current,
high voltage rating, and low ESR make them ideal for
switching regulator applications. Since the LTC3541s
control loop does not depend on the output capacitors
ESR for stable operation, ceramic capacitors can be used
freely to achieve very low output ripple and small circuit
size.
However, care must be taken when ceramic capacitors
are used at the input and the output. When a ceramic
capacitor is used at the input and the power is supplied
by a wall adapter through long wires, a load step at the
output can induce ringing at the input, V
IN
. At best, this
ringing can couple to the output and be mistaken as loop
instability. At worst, a sudden inrush of current through
the long wires can potentially cause a voltage spike at V
IN
,
large enough to damage the part.
When choosing the input and output ceramic capacitors,
choose the X5R or X7R dielectric formulations. These
dielectrics have the best temperature and voltage charac-
teristics of all the ceramics for a given value and size.
Output Voltage Programming
The output voltage is set by tying BUCKFB to a resistive
divider according to the following formula:
V
R
R
OUT
=    +
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
08 1
2
1
.
Since the impedance at the BUCKFB pin is dependant upon
the resistor divider network used, and phase shift due to
this impedance directly impacts the transient response of
the buck, R1 should be chosen <125k. In addition, stray
capacitance at this pin should be minimized (<5pF) to pre-
vent excessive phase shift. Finally, special attention should
be given to any stray capacitances that can couple external
signals onto the BUCKFB pin producing undesirable output
ripple. For optimum performance connect the BUCKFB
pin to R1 and R2 with a short PCB trace and minimize all
other stray capacitance to the BUCKFB pin.
The external resistive divider is connected to the output,
allowing remote voltage sensing as shown in Figure 6.
Checking Transient Response
The regulator loop response can be checked by looking
at the load transient response. Switching regulators take
several cycles to respond to a step in load current. When
a load step occurs, V
OUT
immediately shifts by an amount
equal to (擨
LOAD
" ESR), where ESR is the effective series
Figure 6. Setting the LTC3541 Output Voltage
BUcKFB
GND
LTc3541
0.8V d V
OUT
 d 5V
R2
R1
相關PDF資料
PDF描述
LTC3670EDDB#TRPBF IC REG TRPL BCK/LINEAR 12DFN
LTC3672BEDC-1#TRPBF IC REG TRPL BCK/LINEAR 8-DFN
LTC3700EMS#TRPBF IC REG DL BUCK/LINEAR 10MSOP
LTC4151HMS#TRPBF IC PWR MONITOR MS 80V SD 10MSOP
LTC4210-2CS6#TRM IC CONTROLLER HOT SWAP TSOT23-6
相關代理商/技術參數
參數描述
LTC3542 制造商:LINER 制造商全稱:Linear Technology 功能描述:500mA, 2.25MHz Synchronous Step-Down DC/DC Converter
LTC3542-1 制造商:LINER 制造商全稱:Linear Technology 功能描述:500mA, 2.25MHz 2.8V Output Synchronous Step-Down DC/DC Converter
LTC3542EDC#PBF 制造商:Linear Technology 功能描述:DC-DC CONVERTER BUCK 2.25MHZ 制造商:Linear Technology 功能描述:DC-DC CONVERTER, BUCK, 2.25MHZ, 500mA, DFN-6; Primary Input Voltage:5.5V; No. of Outputs:1; Output Current:500mA; No. of Pins:6; Operating Temperature Min:-40C; Operating Temperature Max:85C; Package / Case:6-DFN ;RoHS Compliant: Yes
LTC3542EDC#TRMPBF 功能描述:IC REG BUCK SYNC ADJ 0.5A 6DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:High Efficiency Current Mode Switching Regulators CMOS LDO Regulators 特色產品:BD91x Series Step-Down Regulators 標準包裝:2,500 系列:- 類型:降壓(降壓) 輸出類型:兩者兼有 輸出數:2 輸出電壓:3.3V,0.8 V ~ 2.5 V 輸入電壓:4.5 V ~ 5.5 V PWM 型:電流模式 頻率 - 開關:1MHz 電流 - 輸出:1.5A 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:VQFN020V4040 產品目錄頁面:1373 (CN2011-ZH PDF) 其它名稱:BD9152MUV-E2TR
LTC3542EDC#TRPBF 功能描述:IC REG BUCK SYNC ADJ 0.5A 6DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:500 系列:- 類型:切換式電容器(充電泵),反相 輸出類型:固定 輸出數:1 輸出電壓:-3V 輸入電壓:2.3 V ~ 5.5 V PWM 型:Burst Mode? 頻率 - 開關:900kHz 電流 - 輸出:100mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型,TSOT-23-6 包裝:帶卷 (TR) 供應商設備封裝:TSOT-23-6 其它名稱:LTC1983ES6-3#TRMTR
主站蜘蛛池模板: 玉山县| 夹江县| 阿克苏市| 若尔盖县| 苏尼特右旗| 新营市| 宜君县| 中宁县| 南华县| 合山市| 北辰区| 澄迈县| 鹰潭市| 涿州市| 尤溪县| 博客| 五原县| 枣庄市| 镇原县| 怀宁县| 江津市| 白沙| 正镶白旗| 禹城市| 江永县| 湟中县| 万山特区| 扎赉特旗| 通州区| 泾川县| 宜君县| 佛冈县| 龙门县| 上饶市| 平阳县| 通化县| 自治县| 东辽县| 公安县| 安达市| 罗城|