欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MAX1765EUE+
廠商: Maxim Integrated
文件頁數: 12/19頁
文件大小: 867K
描述: IC REG DL BST/LINEAR 16TSSOP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 96
拓撲: 升壓(升壓)同步(1),線性(LDO)(1)
功能: 任何功能
輸出數: 2
頻率 - 開關: 1MHz
電壓/電流 - 輸出 1: 2.5 V ~ 5.5 V,800mA
電壓/電流 - 輸出 2: 2.85V/可調,500mA
帶 LED 驅動器:
帶監控器:
帶序列發生器:
電源電壓: 0.7 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 16-TSSOP(0.173",4.40mm)裸露焊盤
供應商設備封裝: 16-TSSOP-EP
包裝: 管件
PWM Operation in Normal Mode
The MAX1765 transitions to fixed-frequency PWM oper-
ation under medium and heavy loads. The N-channel
FET is engaged when V
FB
< V
REF
and is kept on to
ramp up the current in the inductor until one of the fol-
lowing conditions occurs: the system needs are met,
the next falling edge of the internal oscillator is
achieved, or the maximum inductor current (ISET) is
reached. The N-channel is turned off, activating the P-
channel synchronous rectifier that remains on until the
inductor current gets to the P-channel turn-off current
level, or V
FB
< V
REF
and there is a rising oscillator
clock edge. The 1MHz fixed-frequency operation pro-
duces an easily filtered fixed-noise spectrum.
Forced PWM Operation
When CLK/SEL is high, the MAX1765 operates in a low-
noise PWM-only mode. The N-channel FET is turned on
when V
FB
< V
REF
and is kept on to ramp up the induc-
tor current until one of the following conditions occurs:
the system needs are met, the next falling edge of the
internal oscillator is achieved, or the ISET is reached.
The N-channel is then turned off, activating the P-chan-
nel synchronous rectifier that remains on until the next
rising edge of the oscillator, where the N-channel is
again turned on under most conditions. The P-channel
zero detect circuitry is deactivated in forced PWM
mode. This means an N- or P-channel FET is on all the
time for most load conditions.
At light loads, the P-channel will remain on so the
device can pass current back to the input from the out-
put. The P-channel will only pass current for two cycles
before it is disabled. Then, the device remains inactive
until V
FB
< V
REF
.
During forced PWM operation, the MAX1765 switches
at a constant frequency (1MHz) and modulates the
MOSFET switch pulse width to control the power trans-
ferred per cycle in order to regulate the output voltage
for most output currents. Switching harmonics generat-
ed by fixed-frequency operation are consistent and
easily filtered. (See the Boost Followed by LDO Output
Noise Spectrum plot in the Typical Operating
Characteristics.)
Synchronized PWM Operation
The MAX1765 can be synchronized in PWM mode to
an external frequency of 500kHz to 1.2MHz by applying
an external clock signal to CLK/SEL. This allows inter-
ference to be minimized in wireless applications. The
synchronous rectifier is active during synchronized
PWM operation.
Synchronous Rectifier
The MAX1765 features an internal 250m? P-channel
synchronous rectifier to enhance efficiency. Synchronous
rectification provides a 5% efficiency improvement over
similar nonsynchronous boost regulators. In PWM mode,
the synchronous rectifier is turned on during the second
portion of each switching cycle. At light loads (in normal
mode), an internal comparator turns on the synchronous
rectifier when the voltage at LX exceeds the boost regu-
lator output, and turns it off when the inductor current
drops below 50mA.
Low-Voltage Startup Oscillator
The MAX1765 uses a low-voltage startup oscillator for a
1.1V guaranteed minimum input startup input voltage.
A Schottky diode placed across LX and POUT reduces
the startup voltage to 0.9V. At startup, the low-voltage
oscillator switches the N-channel MOSFET until the out-
put voltage reaches 2.15V. Above this level, the normal
boost-converter feedback and control circuitry takes
over. Once the device is in regulation, it can operate
down to 0.7V input since internal power for the IC is
bootstrapped from the OUT pin. Do not apply full load
until the output exceeds 2.3V.
800mA, Low-Noise, Step-Up DC-DC Converter
with 500mA Linear Regulator
12 ______________________________________________________________________________________
Figure 2. Typical Application Circuit
CLK/SELPGND
GND
ONL
TRACK
ONB
4.7糉
FBL
OUTL
33糉
3.3糎
REF
ILIM
4.7?/DIV>
LX
POUT
OUT
FB
LOGIC INPUTS
0.22糉
100糉
0.68糉
0.7V to 3.2V
MAX1765
ONA
V
IN
V
OUTL
=
 2.85V
100k
165k
V
OUT
3.3V
INL
相關PDF資料
PDF描述
MAX1989MUE+ IC TEMP SENSOR REMOTE 16TSSOP
MAX31723MUA+ IC THERMOMETER/STAT SPI-3W 8UMAX
MAX31826MUA+T IC TEMP SENSOR DIGITAL 8UMAX
MAX4006EUT+T IC CURRENT MONITOR 1% SOT23-6
MAX4008EUT+T IC CURRENT MONITOR 1% SOT23-6
相關代理商/技術參數
參數描述
MAX1765EUE+ 功能描述:直流/直流開關轉換器 800mA Step-Up w/500mA Linear Reg RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
MAX1765EUE+T 功能描述:直流/直流開關轉換器 800mA Step-Up w/500mA Linear Reg RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
MAX1765EUE-T 功能描述:直流/直流開關轉換器 800mA Step-Up w/500mA Linear Reg RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
MAX1765EVKIT 功能描述:直流/直流開關轉換器 Evaluation Kit for the MAX1765 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
MAX176ACPA 功能描述:模數轉換器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
主站蜘蛛池模板: 临夏县| 上思县| 淳安县| 和林格尔县| 高陵县| 武功县| 丁青县| 乡宁县| 萍乡市| 内丘县| 肥东县| 陵水| 宁城县| 德保县| 岳西县| 那曲县| 苏尼特左旗| 尼玛县| 保山市| 伊通| 临西县| 谢通门县| 石阡县| 东乡族自治县| 禹城市| 静安区| 那曲县| 承德市| 西和县| 台北市| 平乐县| 华蓥市| 如皋市| 武宣县| 随州市| 林周县| 海城市| 临洮县| 宁波市| 济阳县| 瓮安县|