欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MAX1765EUE+
廠商: Maxim Integrated
文件頁數: 16/19頁
文件大小: 867K
描述: IC REG DL BST/LINEAR 16TSSOP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 96
拓撲: 升壓(升壓)同步(1),線性(LDO)(1)
功能: 任何功能
輸出數: 2
頻率 - 開關: 1MHz
電壓/電流 - 輸出 1: 2.5 V ~ 5.5 V,800mA
電壓/電流 - 輸出 2: 2.85V/可調,500mA
帶 LED 驅動器:
帶監控器:
帶序列發生器:
電源電壓: 0.7 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 16-TSSOP(0.173",4.40mm)裸露焊盤
供應商設備封裝: 16-TSSOP-EP
包裝: 管件
should have a saturation current rating exceeding the
N-channel switch current limit; however, it is accept-
able to bias the inductor current into saturation by as
much as 20% if a slight reduction in efficiency is
acceptable. Lower current-rated inductors may be
used if ISET is employed to reduce the peak inductor
current (see Setting the Switch Current Limit and Soft-
Start). For high efficiency, choose an inductor with a
high-frequency core material to reduce core losses. To
minimize radiated noise, use a toroid or shielded induc-
tor. See Table 3 for suggested components and Table
4 for a list of component suppliers.
Output Diode
To assist startup with input voltages below 1.1V or
when V
OUT
is set for >4V, use a Schottky diodesuch
as a 1N5817, MBR0520L or equivalentbetween LX
and POUT (Figure 2). The Schottky diode carries cur-
rent after the synchronous rectifier turns off. Thus, its
current rating only needs to be 500mA. Connect the
diode as close to the IC as possible. Do not use ordi-
nary rectifier diodes; their slow switching speeds and
long reverse-recovery times render them unacceptable.
For input voltages over 1.8V, the Schottky diode may
improve light-load efficiency.
Input and Output Filter Capacitors
Choose input and output filter capacitors that will ser-
vice the input and output peak currents with accept-
able voltage ripple. Choose input capacitors with
working voltage ratings over the maximum input volt-
age and output capacitors with working voltage ratings
higher than the output. A 100礔, 100m? low equiva-
lent-series-resistance (ESR) tantalum output capacitor
is recommended for most applications. At the output of
the linear regulator (OUTL), use a 4.7礔 ceramic
capacitor for stability at loads up to 500mA.
The input filter capacitor reduces peak currents drawn
from the input source and also reduces input switching
noise. The input voltage source impedance determines
the required size of the input capacitor. When operat-
ing directly from one or two NiMH cells placed close to
the MAX1765, use a single 33礔 low-ESR input filter
capacitor.
The Sanyo POSCAP, Panasonic SP/CB, and Kemet
T510 are good low-ESR capacitors. Low-ESR tantalum
capacitors offer a good trade-off between price and
performance. Do not exceed the ripple current ratings
of tantalum capacitors. Avoid aluminum electrolytic
capacitors; their high ESR typically results in higher
output ripple voltage.
Bypass Capacitors
Bypass REF to GND with 0.22礔. Also, bypass OUT to
GND with a 0.68礔 ceramic capacitor, and connect
OUT to POUT with a 4.7﹔esistor. Each of these com-
ponents should be placed as close to its respective IC
pins as possible, within 0.2in (5mm).
Layout Considerations
High switching frequencies and large peak currents
make PC board layout a critical part of design. Poor
design will cause excessive EMI and ground bounce,
both of which can cause instability or regulation errors
by corrupting the voltage and current feedback signals.
Power componentssuch as the inductor, converter
IC, filter capacitors, and output diodeshould be
placed as close together as possible, and their traces
should be kept short, direct, and wide. Connect the
inductor from the battery to the LX pins as close to the
IC as possible.
Keep the voltage feedback network very close to the
IC, within 0.2in (5mm) of the FB pins. Keep noisy
traces, such as those from the LX pin, away from the
voltage feedback networks and guarded from them
using grounded copper. Refer to the MAX1765 EV kit
for a full PC board example.
800mA, Low-Noise, Step-Up DC-DC Converter
with 500mA Linear Regulator
16 ______________________________________________________________________________________
Figure 7. Feedback Connections
MAX1765
INL
OUTL
POUT
OUT
FBL
FB
GND
PGND
R3
R4
R2
R1
STEP-UP
OUTPUT
LINEAR-
REGULATOR
OUTPUT
相關PDF資料
PDF描述
MAX1989MUE+ IC TEMP SENSOR REMOTE 16TSSOP
MAX31723MUA+ IC THERMOMETER/STAT SPI-3W 8UMAX
MAX31826MUA+T IC TEMP SENSOR DIGITAL 8UMAX
MAX4006EUT+T IC CURRENT MONITOR 1% SOT23-6
MAX4008EUT+T IC CURRENT MONITOR 1% SOT23-6
相關代理商/技術參數
參數描述
MAX1765EUE+ 功能描述:直流/直流開關轉換器 800mA Step-Up w/500mA Linear Reg RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
MAX1765EUE+T 功能描述:直流/直流開關轉換器 800mA Step-Up w/500mA Linear Reg RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
MAX1765EUE-T 功能描述:直流/直流開關轉換器 800mA Step-Up w/500mA Linear Reg RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
MAX1765EVKIT 功能描述:直流/直流開關轉換器 Evaluation Kit for the MAX1765 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
MAX176ACPA 功能描述:模數轉換器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
主站蜘蛛池模板: 泗洪县| 安宁市| 尉犁县| 全南县| 乃东县| 阜新市| 大悟县| 洱源县| 尖扎县| 磐石市| 武邑县| 视频| 禄劝| 宜城市| 扎赉特旗| 克什克腾旗| 石渠县| 如皋市| 两当县| 上栗县| 香港| 克什克腾旗| 民勤县| 分宜县| 黑水县| 清水河县| 辰溪县| 鄯善县| 卢氏县| 恩施市| 和平县| 马山县| 庆云县| 京山县| 新干县| 天气| 贵阳市| 夏邑县| 满洲里市| 清涧县| 丹巴县|