欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MAX5938LEEE+
廠商: Maxim Integrated
文件頁數: 20/26頁
文件大小: 915K
描述: IC HOT-SWAP CTRLR -48V 16-QSOP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 100
類型: 熱交換控制器
應用: 通用
內部開關:
電源電壓: -10 V ~ -80 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 16-SSOP(0.154",3.90mm 寬)
供應商設備封裝: 16-QSOP
包裝: 管件
trol are in the linear range. If this is an issue, an external
resistor, R
GATE
, in series with gate of the MOSFET is rec-
ommended to prevent possible oscillation. It should be as
small as possible, e.g., 5& to 10&, to avoid impacting the
MOSFET turn-off performance of the MAX5938.
Layout Guidelines
To benefit from the temperature compensation designed
into the MAX5938, the part should be placed as close as
possible to the power MOSFET that it is controlling. The
V
EE
pin of the MAX5938 should be placed close to the
source pin of the power MOSFET and they should share
a wide trace. A common top layer plane would service
both the thermal and electrical requirements. The load-
probe current must be taken into account. If this current
is high, the layout traces and current-limiting resistor
must be sized appropriately. Stray inductance must be
minimized in the traces of the overall layout of the hot-
swap controller, the power MOSFET and the load capac-
itor. Starting from the board contacts, all high-current
traces should be short, wide, and direct. The potentially
high pulse current pins of the MAX5938 are GATE (when
pulling GATE low), load probe, and V
EE
. Because of the
nature of the hot-swap requirement no decoupling
capacitor is recommended for the MAX5938. Because
there is no decoupling capacitor, stray inductance may
result in excessive ringing at the GND pin during power-
up or during very rapid V
IN
steps. This should be exam-
ined in every application design since ringing at the
GND pin may exceed the absolute maximum supply rat-
ing for the part.
Input Transient Protection
During hot plug-in/unplug and fast V
IN
steps, stray
inductance in the power path may cause voltage ring-
ing above the normal input DC value, which may
exceed the absolute maximum supply rating. An input
transient such as that caused by lightning can also put
a severe transient peak voltage on the input rail. The
following techniques are recommended to reduce the
effect of transients:
1)  Minimize stray inductance in the power path using
wide traces and minimize loop area including the
power traces and the return ground path.
2)  Add a high-frequency (ceramic) bypass capacitor
on the backplane as close as possible to the plug-
in connector (Figure 20).
3)  Add a 1k& resistor in series with the MAX5938s
GND pin and a 0.1礔 capacitor from GND to V
EE
to
limit transient current going into this pin.
Appendix A
GATE Cycles
The power-up GATE cycle, step GATE cycle, and the OV
GATE cycle are quite similar but have distinct differ-
ences. Understanding these differences may clarify
application issues.
GATE Cycle During Power-Up
The power-up GATE cycle occurs during the initial
power-up of the MAX5938 and the associated power
MOSFET and load. The power-up GATE cycle can
result in full enhancement or in a fault (all voltages are
relative to V
EE
).
Power-Up-to-Full-Enhancement Fault:
1)  At the beginning of the power-up sequence to the
start of the power-up GATE cycle, the GATE is held
at V
EE
. Following a successful completion of the
load-probe test, GATE is held at V
EE
for an additional
350祍 and then is allowed to float for 650祍. At this
point, the GATE begins to ramp with 52礎 charging
the gate of the power MOSFET. [GATE turn-on]
2)  When GATE reaches the gate threshold voltage of
the power MOSFET, V
OUT
begins to ramp down
toward V
EE
. [V
OUT
ramp]
3)  When V
OUT
ramps below 74% V
CB
, the GATE is
rapidly pulled to full enhancement and the power-
up GATE cycle is complete. 1.26ms after GATE is
pulled to full enhancement, PGOOD asserts. [Full
enhancement]
-48V Hot-Swap Controller with V
IN
Step Immunity,
No R
SENSE
, and Overvoltage Protection
20   ______________________________________________________________________________________
Figure 20. Protecting the MAX5938 Input from High-Voltage
Transients
0.1礔
0.1礔
1礔
1k&
100k&
V
EE
PGOOD
GND
BACKPLANE
48V
PLUG-IN CARD
OFF
ON
OV
STEP_MON
相關PDF資料
PDF描述
MAX5939EESA+ IC HOT-SWAP CTRLR -48V 8-SOIC
MAX5946LETX+T IC CNTRLR PCI EXP DL 36TQFN
MAX5948BESA+T IC CNTRLR HOT SWAP 8-SOIC
MAX5949BESA+T IC CNTRLR HOT SWAP 8-SOIC
MAX5950ETJ+ IC PWM CTRL HOT-SW 12V 32TQFN-EP
相關代理商/技術參數
參數描述
MAX5938LEEE+ 功能描述:熱插拔功率分布 48V- Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5938LEEE+T 功能描述:熱插拔功率分布 48V- Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5938LEEE-T 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5939AESA 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5939AESA+ 功能描述:熱插拔功率分布 48V- Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
主站蜘蛛池模板: 呼和浩特市| 阆中市| 新绛县| 瓦房店市| 札达县| 松桃| 衡水市| 盐边县| 齐齐哈尔市| 湖南省| 乌拉特后旗| 清水河县| 罗城| 大渡口区| 彭水| 乐亭县| 德钦县| 台东县| 南宫市| 平陆县| 海林市| 咸宁市| 白玉县| 博乐市| 苏尼特右旗| 新安县| 东源县| 金阳县| 恩平市| 贵定县| 乳源| 英超| 青冈县| 青河县| 开江县| 平邑县| 张家口市| 深圳市| 清苑县| 福安市| 太原市|