- 您現在的位置：買賣IC網 > Datasheet目錄43 > MAX5963UTL+T (Maxim Integrated)IC HOT SWAP DIO ORING CTL 40TQFN Datasheet資料下載
參數資料
| 型號： | MAX5963UTL+T |
| 廠商： | Maxim Integrated |
| 文件頁數： | 16/20頁 |
| 文件大小： | 291K |
| 描述： | IC HOT SWAP DIO ORING CTL 40TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 熱交換控制器 |
| 應用： | FireWire? 應用程序 |
| 內部開關： | 無 |
| 電源電壓： | 7.5 V ~ 76 V |
| 工作溫度： | 0°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 40-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 40-TQFN-EP（6x6） |
| 包裝： | 帶卷 (TR) |
Dual, 7.5V to 76V, Hot-Swap and
Diode ORing Controller
16 ______________________________________________________________________________________
Undervoltage Lockout
The MAX5963 dual-channel, independent current-limit
switches have independent ON/OFF control. Both
channels operate from 7.5V to 76V and have default
6.5V (typ) undervoltage lockout thresholds. The exter-
nal MOSFETs remain off as long as V
PS
< 6.5V or V
ON_
< V
ONTH
. The UVLO thresholds are programmable by
connecting a resistive voltage-divider between ON_
and GND. When V
PS
is greater than 7.5V and V
ON_
exceeds the 1.24V (typ) threshold, GATE1_ and
GATE2_ enhance to 5.5V, with respect to OUT_ and the
MAX5963 switch goes into normal operation.
Calculate the resistor values to program the switches
individual turn-on threshold voltages using the following
formula:
where V
TURN_ON
is the desired turn-on voltage of chan-
nel A and/or B. R
1
and R
2
create a resistive divider
from PS to ON_ (see the Typical Operating Circuit).
When operating the MAX5963, ON_ must remain above
its 1.24V (typ) threshold. If V
ON_
falls below the thresh-
old and hysteresis for more than 10祍 (typ), the power-
supply MOSFETs turn off. This allows the power supply
to disconnect from the load in the event of a fault condi-
tion such as shorting of the output to a different power-
supply voltage or to a FireWire signal pin. If possible
transient conditions exist that may exceed 10祍 (typ) at
the main power-supply line (PS), place an RC filter at
ON_ to reject transient voltage dips to prevent unnec-
essary power-supply interruptions.
Current-Fault Status Output (FAULT_)
FAULTA and FAULTB are high-voltage, open-drain out-
puts that pull low when a current-limit or circuit-breaker
fault shutdown has occurred. FAULTA and FAULTB
remain low until the next startup cycle. FAULTA and
FAULTB are capable of sinking up to 5mA when asserted.
Autoretry/Latchoff Fault Management
The MAX5963 autoretry feature attempts to restart after
an adjustable current-limit or circuit-breaker timeout, lim-
iting the duty cycle of the MOSFETs under continuous
fault conditions. Connect RETRY to BP or PS for
autorestart mode. Leave RETRY floating to select latchoff
mode after a current-limit/circuit-breaker timeout.
FAULT_ deasserts every time a restart attempt is made.
Logic Inputs
Power-Supply Enables (ENX, ENY, and ENZ)
Three enable inputs, ENX, ENY, and ENZ, can be used
to control power-on/power-off.
ENZ is a logic input that is ANDed with the OR combi-
nation of ENX and ENY. Apply a voltage greater than
1.8V (min) to ENZ to ensure that GATEPS is pulled high
when V
PWR
rises above the 6.5V (typ) PWR undervolt-
age lockout threshold.
Pull ENZ low to put the MAX5963 into PWR standby or
shutdown mode. The MAX5963 draws less than 10礎
from PWR in shutdown. See Table 2.
R
V
1.24V
1 x R
1
TURN_ON
2
=
?/DIV>
?/DIV>
主站蜘蛛池模板：
家居|
宣武区|
三江|
安化县|
五大连池市|
阿鲁科尔沁旗|
五常市|
伊春市|
诸城市|
汝州市|
邓州市|
平定县|
榆中县|
黄陵县|
兴业县|
文安县|
华坪县|
内黄县|
谷城县|
洛浦县|
绥滨县|
泸州市|
嘉义市|
方正县|
乌兰察布市|
贵州省|
和静县|
焉耆|
郸城县|
昭苏县|
理塘县|
电白县|
蓝山县|
梁平县|
临桂县|
阜新|
砚山县|
柘城县|
台东县|
芒康县|
彭泽县|
?/DIV>
?/DIV>
?/DIV>
?/DIV>
Table 1. ORing Protection Truth Table
INPUT
OUTPUT
(V
SENSEA
+ V
SENSEB
)/2 > V
OR
GATEOR
DESCRIPTION
Yes
On
Normal operation. ORing MOSFET (QOR) is on to minimize power
dissipation.
No
Off
ORing protection. ORing MOSFET (QOR) is off, preventing current
flowing backward into the systems power supply, V
PWR
.
Table 2. Logic Input Truth Table
INPUT
OUTPUT
(ENX OR ENY) AND ENZ
GATEPS
DESCRIPTION
L
Off
System Power-Off Mode. The MAX5963 draws < 10礎 from PWR after
[(ENX or ENY) and ENZ] goes low for more than t
SHDN
time.
H
On
Enable System Power. The system power supply, V
SUPPLY
, provides
power to the FireWire ports.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5965AEAX+ | IC PSE CTRLR FOR POE 36SSOP |
| MAX5969DETE+T | IC CTRLR INTERFCE W/MOSFT 16TQFN |
| MAX5971AETI+ | IC CTRLR PD IEEE 802.3AF 28WQFN |
| MAX5972AETE+T | IC CONTROLLER INTERFACE 16TQFN |
| MAX5978ETJ+ | IC CTLR HOT-SWAP 32TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5965ACAX+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX5965ACAX+T | 制造商:Maxim Integrated Products 功能描述:HIGH-POWER, QUAD, MONOLITHIC, PSE CONTROLLERS FOR POWER OVER - Tape and Reel |
| MAX5965AEAX+ | 功能描述:熱插拔功率分布 Quad PSE Controller for POE RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5965AEAX+T | 功能描述:熱插拔功率分布 Quad PSE Controller for POE RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5965AUAX+ | 功能描述:熱插拔功率分布 Quad PSE Controller for POE RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。