- 您現在的位置：買賣IC網 > Datasheet目錄43 > MAX6622UE9A+T (Maxim Integrated)IC PREC TEMP MONITOR 5CH 16TSSOP Datasheet資料下載
參數資料
| 型號： | MAX6622UE9A+T |
| 廠商： | Maxim Integrated |
| 文件頁數： | 15/18頁 |
| 文件大小： | 196K |
| 描述： | IC PREC TEMP MONITOR 5CH 16TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -40°C ~ 125°C，外部傳感器 |
| 精確度： | -0.1°C 本地，±3°C 遠程 |
| 拓撲： | ADC，緩沖器，寄存器庫 |
| 輸出類型： | SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 帶卷 (TR) |
5-Channel Precision Temperature Monitor
______________________________________________________________________________________ 15
Discrete Remote Diodes
When the remote-sensing diode is a discrete transistor,
its collector and base must be connected together.
Table 10 lists examples of discrete transistors that are
appropriate for use with the MAX6622. The transistor
must be a small-signal type with a relatively high for-
ward voltage; otherwise, the A/D input voltage range
can be violated. The forward voltage at the highest
expected temperature must be greater than 0.25V at
10礎, and at the lowest expected temperature, the for-
ward voltage must be less than 0.95V at 100礎. Large
power transistors must not be used. Also, ensure that
the base resistance is less than 100? Tight specifica-
tions for forward current gain (50 < ?< 150, for exam-
ple) indicate that the manufacturer has good process
controls and that the devices have consistent V
BE
char-
acteristics. Manufacturers of discrete transistors do not
normally specify or guarantee ideality factor. This is
normally not a problem since good-quality discrete
transistors tend to have ideality factors that fall within a
relatively narrow range. We have observed variations in
remote temperature readings of less than ?癈 with a
variety of discrete transistors. Still, it is good design
practice to verify good consistency of temperature
readings with several discrete transistors from any
manufacturer under consideration.
Unused Diode Channels
If one or more of the remote diode channels is not
needed, the DXP and DXN inputs for that channel
should either be unconnected, or the DXP input should
be connected to V
CC
. The status register indicates a
diode "fault" for this channel and the channel is ignored
during the temperature-measurement sequence. It is
also good practice to mask any unused channels
immediately upon power-up by setting the appropriate
bits in the configuration 2 and configuration 3 registers.
This will prevent unused channels from causing ALERT
or OVERT to assert.
Thermal Mass and Self-Heating
When sensing local temperature, the MAX6622 mea-
sures the temperature of the printed-circuit board (PCB)
to which it is soldered. The leads provide a good ther-
mal path between the PCB traces and the die. As with
all IC temperature sensors, thermal conductivity
between the die and the ambient air is poor by compari-
son, making air temperature measurements impractical.
Because the thermal mass of the PCB is far greater than
that of the MAX6622, the device follows temperature
changes on the PCB with little or no perceivable delay.
When measuring the temperature of a CPU or other IC
with an on-chip sense junction, thermal mass has virtual-
ly no effect; the measured temperature of the junction
tracks the actual temperature within a conversion cycle.
When measuring temperature with discrete remote tran-
sistors, the best thermal response times are obtained
with transistors in small packages (i.e., SOT23 or
SC70). Take care to account for thermal gradients
between the heat source and the sensor, and ensure
that stray air currents across the sensor package do
not interfere with measurement accuracy. Self-heating
does not significantly affect measurement accuracy.
Remote-sensor self-heating due to the diode current
source is negligible.
ADC Noise Filtering
The integrating ADC has good noise rejection for low-
frequency signals, such as power-supply hum. In envi-
ronments with significant high-frequency EMI, connect
an external 2200pF capacitor between DXP_ and
DXN_. Larger capacitor values can be used for added
filtering, but do not exceed 3300pF because it can
introduce errors due to the rise time of the switched
current source. High-frequency noise reduction is
needed for high-accuracy remote measurements.
Noise can be reduced with careful PCB layout as dis-
cussed in the PCB Layout section.
MANUFACTURER
MODEL NO.
Central Semiconductor (USA)
CMPT3904
Rohm Semiconductor (USA)
SST3904
Samsung (Korea)
KST3904-TF
Siemens (Germany)
SMBT3904
Zetex (England)
FMMT3904CT-ND
Table 10. Remote-Sensors Transistor
Manufacturers
Note: Discrete transistors must be diode connected (base
shorted to collector).
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6626RMTT+T | IC TEMP SENSOR I2C 6-TDFN |
| MAX6627MKA#TG16 | IC TEMP SENSOR DGTL SOT23-8 |
| MAX6636UP9A+T | IC PREC TEMP MONITOR 7CH 20TSSOP |
| MAX6639FATE+ | IC 2CH TEMP MONITOR 16TQFN |
| MAX6641AUB92+ | IC TEMP MONITOR SMBUS 10UMAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX66240ETA+ | 制造商:Maxim Integrated Products 功能描述:HF 4KBIT SHA-256 SECURE EEPROM - Rail/Tube |
| MAX66240ETA+T | 制造商:Maxim Integrated Products 功能描述:HF 4KBIT SHA-256 SECURE EEPROM - Tape and Reel |
| MAX6625PMTT+ | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL I2C 6TDFN EP - Rail/Tube |
| MAX6625PMTT+T | 功能描述:板上安裝溫度傳感器 9-Bit/12-Bit Temperature Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6625PMUT | 制造商:Maxim Integrated Products 功能描述:9-BIT TEMPERATURE SENSOR W/ I2CC-COMPATIBLE S - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。