欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MAX6664AEE+T
廠商: Maxim Integrated
文件頁數: 10/24頁
文件大?。?/td> 297K
描述: IC TEMP MON FAN CNTRL 16-QSOP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 2,500
功能: 風扇控制,溫度監控器
傳感器類型: 內部和外部
感應溫度: -40°C ~ 125°C,外部傳感器
精確度: ±2°C 本地(最大),±3°C 遠程(最大)
拓撲: ADC,多路復用器,寄存器庫,測速計
輸出類型: I²C?/SMBus?
輸出警報:
輸出風扇:
電源電壓: 3 V ~ 5.5 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 16-SSOP(0.154",3.90mm 寬)
供應商設備封裝: 16-QSOP
包裝: 帶卷 (TR)
Temperature Monitors and
PWM Fan Controllers
10   ______________________________________________________________________________________
INT is an open-drain digital output that reports the sta-
tus of temperature interrupt limits and fan out-of-limit
conditions. Set bit 1 of configuration register 1 (00h) to
1 to enable INT output or reset this bit to zero to disable
the INT output function. Status register 1 contains sta-
tus information for the conditions that cause INT to
assert. Reading status register 1 resets INT, but INT is
reasserted if the fault condition still exists. Connect a
10k& pullup resistor between INT and V
CC
.
SDL and SDR are open-drain digital outputs on the
MAX6653 that can be used to shut the system down
based on the local (die) temperature of the MAX6653 or
the temperature of the remote sensor, respectively. The
trip thresholds for SDL and SDR are normally set above
the THERM and INT limits. Their power-up values are
set by the CRIT1 and CRIT0 pins, as shown in Table 1.
Fan-Speed Control
The MAX6653/MAX6663/MAX6664 fan-control section
can operate in one of three modes depending on the set-
ting of bit 7 to bit 5 of configuration register 1 (00h).
Regardless of the mode of operation, the PWM output fre-
quency is programmable, and the fan speed is measured
with the result stored in the fan-speed register (08h).
PWM Output Frequency
The PWM output frequency is programmed by bit 5, bit
4, and bit 3 of the fan characteristics register (20h),
regardless of the mode of operation. See Table 7.
Fan-Control Mode
The mode of fan-speed control operation is set by bit 7,
bit 6, and bit 5 in configuration register 1 (00h), as
shown in Table 8.
PWM Duty-Cycle Fan-Control Mode
Bits [3:0] of the fan-speed configuration register set the
PWM duty cycle. See Table 9 for more details.
RPM Select Fan-Control Mode
In RPM select mode, the MAX6653/MAX6663/MAX6664
adjust their PWM output duty cycle to match a selected
fan speed measured by a tachometer count value. Before
selecting this mode by setting bits [7:5] of configuration
register 1 (00h) to 0x1, the desired tachometer count
value should be written to the fan tachometer high-limit
register (10h). In this mode, the MAX6653/MAX6663/
MAX6664 are not able to detect underspeed fan faults
because the fan tachometer high-limit register (10h) func-
tions as the target tachometer count.
The MAX6653/MAX6663/MAX6664 detect fan stall
faults by comparing the fan-speed reading to the full-
scale constant of 254 (FEh). Therefore, the
MAX6653/MAX6663/MAX6664 signal a fan fault when
the fan-speed reading is 255 (FFh). Note that the RPM
mode cannot be used for speeds below 10% of the
fans maximum speed. It is important to verify that a fan
works properly at lower RPM values if a low-RPM oper-
ation in this mode is desired.
Bits [7:5]
MODE OF OPERATION
DESCRIPTION
0x0
PWM duty-cycle mode
Directly program the PWM duty cycle by writing to bits [3:0] of the fan-speed
configuration register (22h).
0x1
RPM select mode
Program the desired fan speed by writing to the fan tachometer high-limit register
(10h). This value should be written after selecting the RPM mode. The
MAX6653/MAX6663/MAX6664 then adjust the PWM duty cycle to cause the fan to
spin at the programmed speed.
100
Automatic mode
PWM duty cycle is automatically controlled by the remote temperature.
111
Automatic mode
PWM duty cycle is automatically controlled by both the remote and the local
temperatures. See the Automatic Fan-Control Mode section.
Table 8. Setting the Fan-Speed Control Mode (Default = 100)
FAN CHARACTERISTICS REGISTER
(20H) POR = 011
BIT 5
BIT 4
BIT 3
PWM
FREQUENCY
(Hz)
0
0
0
11.7
0
0
1
15.6
0
1
0
23.4
0
1
1
31.25
1
0
0
37.5
1
0
1
46.9
1
1
0
62.5
1
1
1
93.5
Table 7. Setting PWM Output Frequency
相關PDF資料
PDF描述
MAX6665ASA45+ IC FAN CNTRL/DRVR 8-SOIC
MAX6670AUB45+ IC TEMP SENSOR REMOTE 10-UMAX
MAX6678AEP92+ IC TEMP MONITOR 2CH PWM 20-QSOP
MAX6681MEE+ IC TEMP SENSOR SMBUS 16-QSOP
MAX6689UP34+ IC 7CH PREC TEMP MONITOR 20TSSOP
相關代理商/技術參數
參數描述
MAX6664AEE-TG075 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX6665ASA070 制造商:Maxim Integrated Products 功能描述:
MAX6665ASA40 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MAX6665ASA40+ 功能描述:馬達/運動/點火控制器和驅動器 Fan Controller Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MAX6665ASA40+T 功能描述:馬達/運動/點火控制器和驅動器 Fan Controller Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
主站蜘蛛池模板: 渑池县| 秦皇岛市| 磐石市| 米林县| 高唐县| 汶上县| 安徽省| 宿松县| 黔西| 和龙市| 青河县| 呼图壁县| 赤城县| 淳化县| 曲麻莱县| 顺昌县| 乐亭县| 恩平市| 祁阳县| 柳河县| 靖州| 尚义县| 饶河县| 云南省| 那坡县| 大庆市| 澄迈县| 岗巴县| 清水县| 小金县| 丰镇市| 呼玛县| 呈贡县| 雷州市| 灵山县| 古蔺县| 江口县| 东兰县| 涞水县| 自治县| 长丰县|