- 您現在的位置：買賣IC網 > Datasheet目錄44 > MAX6664AEE+T (Maxim Integrated)IC TEMP MON FAN CNTRL 16-QSOP Datasheet資料下載
參數資料
| 型號： | MAX6664AEE+T |
| 廠商： | Maxim Integrated |
| 文件頁數： | 5/24頁 |
| 文件大小： | 297K |
| 描述： | IC TEMP MON FAN CNTRL 16-QSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 功能： | 風扇控制，溫度監控器 |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -40°C ~ 125°C，外部傳感器 |
| 精確度： | ±2°C 本地（最大），±3°C 遠程（最大） |
| 拓?fù)洌?/td> | ADC，多路復用器，寄存器庫，測速計 |
| 輸出類型： | I²C?/SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-QSOP |
| 包裝： | 帶卷 (TR) |
Temperature Monitors and
PWM Fan Controllers
_______________________________________________________________________________________ 5
PIN
MAX6653
QSOP
MAX6663/
MAX6664
QSOP
NAME
FUNCTION
1
1
PWM_OUT
Digital Output (Open Drain). Pulse-width modulated output to external power transistor.
Requires a pullup resistor (10k& typ).
2
2
TACH/AIN
Digital/Analog Input. Fan tachometer input. May be reprogrammed as an analog input to
measure speed of a 2-wire fan. See Figure 5.
3
CRIT0
Input. Used in conjunction with CRIT1 to set THERM and SHUTDOWN default set points
(see Table 1).
4
CRIT1
Input. Used in conjunction with CRIT0 to set THERM and SHUTDOWN default set points
(see Table 1).
3, 4
N.C.
No Connection. Not internally connected.
5
5
GND
Ground
6
6
V
CC
Power Supply. Bypass with a 0.01礔 capacitor to GND.
7
7
THERM
Digital I/O (Open Drain). An active-low thermal-overload output to indicate that the
overtemperature set point has been exceeded. Also acts as an input to provide external
fan control. When this pin is pulled low by an external signal, a status bit is set and the
fan speed is forced full-on. Requires a pullup resistor (10k& typ).
8
8
FAN_FAULT
Digital Output (Active Low, Open Drain). Signals a fan fault. Requires a pullup resistor
(10k& typ).
9
9
DXN
Combined Current Sink and A/D Negative Input. DXN is internally biased to a diode
voltage above ground.
10
10
DXP
Combined Current Source and A/D Positive Input for the Remote-Diode Channel. Do not
leave DXP floating; connect DXP to DXN if no remote diode is used. Place a 2200pF
capacitor between DXP and DXN for noise filtering.
11
SDL
An Active-Low Open-Drain Output. It indicates that local temperature is above the
shutdown set point. Normally used to directly deactivate the CPU power supply.
12
SDR
An Active-Low Open-Drain Output. It indicates that remote temperature is above the
shutdown set point. Normally used to directly deactivate the CPU power supply.
11, 12
N.C.
Internal Connection. Leave floating or connect to GND.
13
13
ADD
Three-State Logic Input. Sets the 2 lower bits of the device SMBus address (Table 2).
ADD is not an ordinary logic input pin; ADD should be connected to V
CC
, GND, or float.
14
14
INT
Digital Output (Open Drain). Can be programmed as an interrupt output for
temperature/fan speed interrupts. Requires a pullup resistor (10k& typ). For the
MAX6653/MAX6663, it can be used also as an input. If pulled low, fan speed is forced to
maximum unless masked.
15
15
SMBDATA
SMBus Serial-Data Input/Output (Open Drain). Requires a pullup resistor (10k& typ).
16
16
SMBCLK
SMBus Serial-Clock Input. Requires a pullup resistor (10k& typ).
12
N.C.
Internal Connection. Leave floating or connect to GND.
Pin Description
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6665ASA45+ | IC FAN CNTRL/DRVR 8-SOIC |
| MAX6670AUB45+ | IC TEMP SENSOR REMOTE 10-UMAX |
| MAX6678AEP92+ | IC TEMP MONITOR 2CH PWM 20-QSOP |
| MAX6681MEE+ | IC TEMP SENSOR SMBUS 16-QSOP |
| MAX6689UP34+ | IC 7CH PREC TEMP MONITOR 20TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6664AEE-TG075 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX6665ASA070 | 制造商:Maxim Integrated Products 功能描述: |
| MAX6665ASA40 | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MAX6665ASA40+ | 功能描述:馬達/運動/點火控制器和驅動器 Fan Controller Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MAX6665ASA40+T | 功能描述:馬達/運動/點火控制器和驅動器 Fan Controller Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。