- 您現在的位置：買賣IC網 > PDF目錄382289 > MBM29PL12LM10PCN (FUJITSU LTD) FLASH MEMORY 128 M (16M ?8/8M ?16) BIT PDF資料下載
參數資料
| 型號： | MBM29PL12LM10PCN |
| 廠商： | FUJITSU LTD |
| 元件分類： | DRAM |
| 英文描述： | FLASH MEMORY 128 M (16M ?8/8M ?16) BIT |
| 中文描述： | 8M X 16 FLASH 3V PROM, 100 ns, PDSO56 |
| 封裝： | PLASTIC, TSOP1-56 |
| 文件頁數： | 27/72頁 |
| 文件大小： | 1036K |
| 代理商： | MBM29PL12LM10PCN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
MBM29PL12LM
10
27
Temporary Sector Group Unprotection
This feature allows temporary unprotection of previously protected sector groups of the devices in order to
change data. The Sector Group Unprotection mode is activated by setting the RESET pin to high voltage (V
ID
).
During this mode, formerly protected sector groups can be programmed or erased by selecting the sector group
addresses. Once the V
ID
is taken away from the RESET pin, all the previously protected sector groups will be
protected again. Refer to “Temporary Sector Group Unprotection Timing Diagram” in
■
TIMING DIAGRAM and
“Temporary Sector Group Unprotection Algorithm” in
■
FLOW CHART.
Hardware Reset
The devices may be reset by driving the RESET pin to V
IL
from V
IH
. The RESET pin has a pulse requirement
and has to be kept low (V
IL
) for at least “t
RP
” in order to properly reset the internal state machine. Any operation
in the process of being executed will be terminated and the internal state machine will be reset to the read mode
“t
READY
” after the RESET pin is driven low. When the RESET pin is low, the devices will be in the standby mode
for the duration of the pulse and all the data output pins will be tri-stated. If a hardware reset occurs during a
program or erase operation, the data at that particular location will be corrupted.
Furthermore, once the RESET pin goes high, the devices require an additional “t
RH
” before it will allow read
access.
Write Protect (WP)
The Write Protection function provides a hardware method of protecting certain first 64K bytes / 32K words
sector without using V
ID
. This function is one of two provided by the WP/ACC pin.
If the system asserts V
IL
on the WP/ACC pin, the device disables program and erase functions in the first 64K
bytes / 32K words sector independently of whether this sector was protected or unprotected using the method
described in “Sector Group Protection" above.
If the system asserts V
IH
on the WP/ACC pin, the device reverts of whether the first 64K bytes / 32K words
sectors were last set to be protected to the unprotected status. Sector protection or unprotection for this sector
depends on whether this was last protected or unprotected using the method described in “Sector protection/
unprotection”.
Accelerated Program Operation
The device offers accelerated program operation which enables programming in high speed. If the system asserts
V
ACC
to the WP/ACC pin, the device automatically enters the acceleration mode and the time required for program
operation will reduce to about 85%. This function is primarily intended to allow high speed programing, so caution
is needed as the sector group becomes temporarily unprotected.
The system would use a fast program command sequence when programming during acceleration mode. Set
command to fast mode and reset command from fast mode are not necessary. When the device enters the
acceleration mode, the device is automatically set to fast mode. Therefore, the present command and sequence
could be used for programming and detection of completion during acceleration mode.
Removing V
ACC
from the WP/ACC pin returns the device to normal operation. Do not remove V
ACC
from the WP/
ACC pin while programming. See “Accelerated Program Timing Diagram” in
■
TIMING DIAGRAM.
V
CCQ
V
CCQ
determines the MBM29PL12LM voltage output. V
CCQ
facilitates signal exchange within devices that operate in different
voltage.
相關PDF資料 |
PDF描述 |
|---|---|
| MBM30LV0064-PFTN | 64M (8M X 8) BIT NAND-type |
| MBM30LV0064-PFTR | 64M (8M X 8) BIT NAND-type |
| MBM30LV0032 | 32M (4M X 8) BIT NAND-type |
| MBM30LV0032-PFTN | 32M (4M X 8) BIT NAND-type |
| MBM30LV0032-PFTR | RES 150-OHM 1% 0.063W 200PPM THICK-FILM SMD-0402 10K/REEL-7IN-PA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MBM30000 | 功能描述:BRACKET SIDE MOUNT RoHS:是 類別:工業控制，儀表 >> 配件 系列:* 標準包裝:1 系列:Aero-Motive® 130117 附件類型:拖車帶 適用于相關產品:標準盒式跟蹤系統 其它名稱:WM6183 |
| MBM30035001 | 制造商:LG Corporation 功能描述:Card,Technical |
| MBM30035015 | 制造商:LG Corporation 功能描述:Card,Technical |
| MBM300A6 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES |
| MBM300GR12A | 制造商:n/a 功能描述:IGBT Module |
發布緊急采購，3分鐘左右您將得到回復。