欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號： MBM29PL12LM10PCN
廠商： FUJITSU LTD
元件分類： DRAM
英文描述： FLASH MEMORY 128 M (16M ?8/8M ?16) BIT
中文描述： 8M X 16 FLASH 3V PROM, 100 ns, PDSO56
封裝： PLASTIC, TSOP1-56
文件頁數： 29/72頁
文件大小： 1036K
代理商： MBM29PL12LM10PCN
MBM29PL12LM
10
29
Programming is allowed in any address sequence and across sector boundaries. Beware that a data “0” cannot
be programmed back to a “1”. Attempting to do so may result in either failure condition or an apparent success
according to the data polling algorithm. But a read from reset command will show that the data is still “0”. Only
erase operations can convert “0”s to “1”s.
Note that attempting to program a “1” over a “0” will result in programming failure. This precaution is the same
with Fujitsu standard NOR devices. “Embedded Program
TM
Algorithm” in
■
FLOW CHART illustrates the Em-
bedded Program
TM
Algorithm using typical command strings and bus operations.
Program Suspend/Resume
The Program Suspend command allows the system to interrupt a program operation so that data can be read
from any address. Writing the Program Suspend command (B0h) during Embedded Program operation imme-
diately suspends the programming. Refer to "Erase Suspend/Resume" for the detail.
When the Program Suspend command is written during a programming process, the chip halts the program
operation within 1
μ
s and suspend the status bits.After the program operation has been suspended, the system
can read data from any address. Normal read timing and command definitions apply. The data at program-
suspended address is not valid.
After the Program Resume command (30h) is written, the chip reverts to programming. The system can determine
the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard program operation.
See "Write Operation Status" for more information.
When issuing program suspend command in 4
μ
s after issuing program command, determine the status of
program operation by reading status bit at more 4
μ
s after issuing program resume command.
The system also writes the Autoselect command sequence in the Program Suspend mode. The device allows
reading Autoselect codes at the addresses within programming sectors, since the codes are not stored in the
memory. When the device exits the Autoselect mode, the device reverts to the Program Suspend mode, and is
ready for another valid operation. See "Autoselect Command Sequence" for more information.
The system must write the Program Resume command to exit from the Program Suspend mode and continue
the programming operation. Further writes of the Resume command are ignored. Another Program Suspend
command can be written after the chip resumes programming.
Write Buffer Programming Operations
Write Buffer Programming allows the system write to series of 16 words in one programming operation. This
results in faster effective word programming time than the standard programming algorithms. The Write Buffer
Programming command sequence is initialized by first writing two unlock cycles. This is followed by a third write
cycle selecting the Sector Address in which programming will occur. In forth cycle contains both Sector Address
and unique code for data bus width will be loaded into the page buffer at the Sector Address in which programming
will occur.
The system then writes the starting address/data combination. This “starting address” must be the same Sector
Address used in third and fourth cycles and its lower addresses of A
3
to A
0
should be 0h. All subsequent address
must be incremented by 000Fh. Addresses are latched on the falling edge of CE or WE, whichever happens
later and the data is latched on the rising edge of CE or WE, whichever happens first. The rising edge of the
last CE or WE (whichever happens first) starts programming. Upon executing the Write Buffer Programming
Operations command sequence, the system is not required to provide further controls. The device will automat-
ically provide adequate internally generated program pulses and verify the programmed cell margin.
DQ
7
(Data Polling), DQ
6
(Toggle Bit), DQ
5
(Exceeded Timing Limits), DQ
1
(Write-to-Buffer Abort) should be mon-
itored to determine the device status during Write Buffer Programming. In addition to these functions, it is also
possible to indicate to the host system that Write Buffer Programming Operations are either in progress or have
been completed by RY/BY. See “Hardware Sequence Flags”.
The Data polling techniques described in “Data Polling Algorithm” in
■
FLOW CHART should be used while
monitoring the last address location loaded into the write buffer. In addition, it is not neccessary to specify an
address in Toggle Bit techniques described in “Toggle Bit Algorithm” in
■
FLOW CHART. The automatic pro-
相關PDF資料
PDF描述
MBM30LV0064-PFTN 64M (8M X 8) BIT NAND-type
MBM30LV0064-PFTR 64M (8M X 8) BIT NAND-type
MBM30LV0032 32M (4M X 8) BIT NAND-type
MBM30LV0032-PFTN 32M (4M X 8) BIT NAND-type
MBM30LV0032-PFTR RES 150-OHM 1% 0.063W 200PPM THICK-FILM SMD-0402 10K/REEL-7IN-PA
相關代理商/技術參數
參數描述
MBM30000 功能描述:BRACKET SIDE MOUNT RoHS:是 類別:工業控制，儀表 >> 配件 系列:* 標準包裝:1 系列:Aero-Motive® 130117 附件類型:拖車帶 適用于相關產品:標準盒式跟蹤系統 其它名稱:WM6183
MBM30035001 制造商:LG Corporation 功能描述:Card,Technical
MBM30035015 制造商:LG Corporation 功能描述:Card,Technical
MBM300A6 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
MBM300GR12A 制造商:n/a 功能描述:IGBT Module
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*
主站蜘蛛池模板： 义乌市| 龙门县| 靖远县| 墨玉县| 太保市| 新宁县| 大荔县| 梁山县| 富源县| 祁阳县| 泽州县| 尼玛县| 梨树县| 盐山县| 夏河县| 高安市| 凌海市| 长子县| 金湖县| 江源县| 台江县| 阿拉尔市| 如皋市| 南部县| 阿勒泰市| 庄浪县| 诏安县| 南部县| 垫江县| 龙江县| 清新县| 唐河县| 天长市| 临漳县| 双柏县| 来安县| 西吉县| 长武县| 朝阳区| 辽源市| 邢台县|