- 您現在的位置：買賣IC網 > PDF目錄382289 > MBM30LV0064-PFTR (FUJITSU LTD) 64M (8M X 8) BIT NAND-type PDF資料下載
參數資料
| 型號： | MBM30LV0064-PFTR |
| 廠商： | FUJITSU LTD |
| 元件分類： | DRAM |
| 英文描述： | 64M (8M X 8) BIT NAND-type |
| 中文描述： | 8M X 8 FLASH 3.3V PROM, 7000 ns, PDSO40 |
| 封裝： | 0.80 MM PITCH, PLASTIC, REVERSE, TSOP2-44/40 |
| 文件頁數： | 30/43頁 |
| 文件大小： | 397K |
| 代理商： | MBM30LV0064-PFTR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
MBM30LV0064
30
(3) Acceptable commands after serial input command ‘80h’
When the serial input command (80h) is input for program execution, commands other than the program execution
command (10h) or reset command (FFh) should not be input.
If a command other than ‘10h’ or ‘FFh’ is input, the program operation is not performed.
(4) Status read during the read operation
When the status read command (70h) is input during reading, the next RE clock signal can be input to read the
value of the internal status register.
Since the internal operation mode is held in Status Read, read data will not be output even if the RE clock signal
is input after becoming ready. Status Read is therefore disabled at reading.
When the read command (00h) is input during the period [A], the internal operation mode of the device can be
canceled, making it possible to read data at address N without inputting Add.
(5) Auto program failure
80
FF
Address input
WE
R/B
Figure 25 Reset Command After 80h Input
10
XX
80
Other command
Programming will not be executed.
In case of this operation, the FFh command
is needed.
00
70
00
[A]
N address
Status read
command input
Status output
Status read
WE
R/B
CE
RE
Figure 26 Status Read During Read Operation
If programming at page address (M) fails, data should be programmed at the
page address (N) of another block.
Data input at first programming at page address (M) is lost. So address input
using the 80h command must follow the same procedure as data input.
80
10
70
80
80
10
I/O
10
Fail
Address
M
Data
input
Address
N
Data
input
N
M
Figure 27 Auto Program Failure
相關PDF資料 |
PDF描述 |
|---|---|
| MBM30LV0032 | 32M (4M X 8) BIT NAND-type |
| MBM30LV0032-PFTN | 32M (4M X 8) BIT NAND-type |
| MBM30LV0032-PFTR | RES 150-OHM 1% 0.063W 200PPM THICK-FILM SMD-0402 10K/REEL-7IN-PA |
| MBM30LV0064 | 64M (8M X 8) BIT NAND-type |
| MBM30LV0128 | RES 1.5K-OHM 1% 0.063W 200PPM THICK-FILM SMD-0402 10K/REEL-7IN-PA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MBM30LV0128 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:128 M (16 M X 8) BIT NAND-type |
| MBM30LV0128-PFTN | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:128 M (16 M X 8) BIT NAND-type |
| MBM30LV0128-PFTR | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:128 M (16 M X 8) BIT NAND-type |
| MBM31048901 | 制造商:LG Corporation 功能描述:Card |
| MBM31262801 | 制造商:LG Corporation 功能描述:Card,Technical |
發布緊急采購，3分鐘左右您將得到回復。