- 您現在的位置：買賣IC網 > PDF目錄382300 > MC28U512HACA-0QC00 (SAMSUNG SEMICONDUCTOR CO. LTD.) MultiMediaCard Specification PDF資料下載
參數資料
| 型號： | MC28U512HACA-0QC00 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | MultiMediaCard Specification |
| 中文描述： | 多媒體卡規格 |
| 文件頁數： | 40/66頁 |
| 文件大小： | 1422K |
| 代理商： | MC28U512HACA-0QC00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
MultiMediaCard
TM
40
*
Setting the Password
- Select a card (CMD7), if not previously selected already
- Define the block length (CMD16), given by the 8bit card lock/unlock mode, the 8-bit password
Size (in bytes), and the number of bytes of the new password. In case that a password
replacement is done, then the block size shall consider that both passwords, the old and the new
one, are sent with the command.
- Send Card Lock/Unlock command with the appropriate data block size on the data line including
16 bit CRC. The data block shall indicate the mode (SET_PWD), the length (PWD_LEN) and the
password itself. In case that a password replacement is done, then the length value (PWD_LEN)
shall include both passwords, the old and the new one, and the PWD field shall include the old
password (currently used) followed by the new password.
In case that the sent old password is not correct (not equal in size and content) then
LOCK_UNLOCK_FAILED error bit will be set in the status register and the old password
password and its size will be saved in the PWD and PWD_LEN fields, respectively.
Note that the password length register (PWD_LEN) indicates if a password is currently set. When it
equals ‘0’ there is no password set. If the value of PWD_LEN is not equal to zero the card will lock
itself after power up. It is possible to lock the card immediately in the current power session by set-
ting the LOCK/UNLOCK bit (while setting the password) or sending additional command for card lock.
* Reset the Password:
- Select a card (CMD7), if not previously selected already
- Define the block length (CMD 16), given by the 8bit card lock/unlock mode, the 8bit password
size (in bytes), and the number of bytes of the currently used password.
- Send the card lock/unlock command with the appropriate data block size on the data line
including 16 bit CRC. The data block shall indicate the mode CLR_PWD, the length (PWD_LEN)
and the password (PWD) itself (LOCK/UNLOCK bit is don’t care). If the PWD and PWD_LEN
content match the sent password and its size, then the content of the PWD register is cleared and
PWD_LEN is set to 0. If the password is not correct then the LOCK_UNLOCK_FAILED error bit
will be set in the status register.
* Locking a card:
- Select a card (CMD7), if not previously selected already
- Define the block length (CMD16), given by the 8 bit card lock/unlock mode, the 8 bit password
size (in bytes), and the number of bytes of the currently used password.
- Send the card lock/unlock command with the appropriate data block size on the data line
including 16 bit CRC. The data block shall indicate the mode LOCK, the length (PWD_LEN) and
the password (PWD) itself.
If the PWD content equals to the sent password then the card will be locked and the card-locked
status bit will be set in the status register. If the password is not correct then
LOCK_UNLOCK_FAILED error bit will be set in the status register. Note that it is possible to set the
password and to lock the card in the same sequence. In such case the host shall perform all the
required steps for setting the password (as described above) including the bit LOCK set while the
new password command is sent. If the password was previously set (PWD_LEN is not ‘0’), then the
card will be locked automatically after power on reset. An attempt to lock a locked card or to lock a
card that does not have a password will fail and the LOCK_UNLOCK_FAILED error bit will be set in
相關PDF資料 |
PDF描述 |
|---|---|
| MC56U016HACA-0QC00 | MultiMediaCard Specification |
| MC28U128HACA-0QC00 | MultiMediaCard Specification |
| MC2DU128HACA-0QC00 | MultiMediaCard Specification |
| MC2DU256HACA-0QC00 | MultiMediaCard Specification |
| MC28U016HACA | MultiMediaCard Specification |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC290 | 制造商:LEDTRN 功能描述: 制造商:LEDtronics Inc 功能描述: |
| MC-290B | 制造商:Panasonic Industrial Company 功能描述:BELT |
| MC29359 | 制造商:SPC Multicomp 功能描述:TERMINAL BUTT SPLICE CRIMP 制造商:SPC Multicomp 功能描述:TERMINAL, BUTT SPLICE, CRIMP 制造商:SPC Multicomp 功能描述:TERMINAL, BUTT SPLICE, CRIMP; Connector Type:Butt Splice; Series:-; Termination Method:Crimp; Wire Size AWG Min:22AWG; Wire Size AWG Max:16AWG; Contact Plating:Tin; Insulator Material:Uninsulated; Wire Size (AWG):22AWG to 16AWG ;RoHS Compliant: Yes |
| MC29360 | 制造商:SPC Multicomp 功能描述:TERMINAL BUTT SPLICE CRIMP 制造商:SPC Multicomp 功能描述:TERMINAL, BUTT SPLICE, CRIMP 制造商:SPC Multicomp 功能描述:TERMINAL, BUTT SPLICE, CRIMP; Connector Type:Butt Splice; Series:-; Termination Method:Crimp; Wire Size AWG Min:22AWG; Wire Size AWG Max:16AWG; Contact Plating:Nickel; Insulator Material:Uninsulated; Wire Size (AWG):22AWG to 16AWG ;RoHS Compliant: Yes |
| MC29361 | 制造商:SPC Multicomp 功能描述:TERMINAL BUTT SPLICE CRIMP 制造商:SPC Multicomp 功能描述:TERMINAL, BUTT SPLICE, CRIMP 制造商:SPC Multicomp 功能描述:TERMINAL, BUTT SPLICE, CRIMP; Connector Type:Butt Splice; Series:-; Termination Method:Crimp; Wire Size AWG Min:16AWG; Wire Size AWG Max:14AWG; Contact Plating:Tin; Insulator Material:Uninsulated; Wire Size (AWG):16AWG to 14AWG ;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。