欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68160FB
廠商: MOTOROLA INC
元件分類: 網絡接口
英文描述: ENHANCED ETHERNET INTERFACE TRANSCEIVER
中文描述: DATACOM, ETHERNET TRANSCEIVER, PQFP52
封裝: PLASTIC, TQFP-52
文件頁數: 26/30頁
文件大小: 372K
代理商: MC68160FB
MC68160 MC68160B MC68160C
26
MOTOROLA ANALOG IC DEVICE DATA
If after approximately 40 ms after a TP or AUI transmission
has begun, the EEST is still transmitting, the TPJABB pin will
assert to signify a jabber condition. Also, the CLLED pin will
transition high and low alternately with a 100 ms period. The
transmit circuitry is, however, unaffected by the jabber
condition, so the communications controller has the
responsibility of monitoring and stopping transmission.
When transmission is complete, the transmit circuitry will
begin the end of transmit and decay to idle responses
necessary to meet requirements of the 802.3 standard for the
TP and AUI port.
Data Reception
Other than the case of being in Loop Back mode, data
reception to the RX pin of the EEST is initiated by signaling at
the RX+/– or AUI ARX+/– pins. If at the TP port, the data is
screened for validity by checking for sequence and pulse
width requirements, then passed to the decode and receive
circuitry. The RENA pin asserts and the data and
corresponding clock is passed to the communications
controller. After the frame has been transmitted, the
MC68160, B and C detects the ending transmission and
negates RENA. If at the AUI port, the data is checked for
proper pulse width requirements before being passed to the
decode circuitry. If the data pulses are longer than at least 20
ns, RENA gets asserted and the frame is decoded to RX with
and accompanying RCLK output.
Collision
Collision is the occurrence of simultaneous transmit
activity by two or more stations on the network. In the event of
collision, the data transfer paths are unaffected. If the
MC68160, B and C is in the twisted pair mode, collision is
detect by simultaneous receive and transmit activity. If in the
AUI mode, collision is detected by activity on the ACX+/–
pins. In either case, if collision is detected, the CLSN pin will
assert to notify the communications controller.
Jabber
The EEST has a jabber timer to detect the jabber condition.
In the event that the transmitting station continues to transmit
beyond the allowable transmit time, a jabber timer (40 ms) will
expire and assert the TPJABB pin to alert the communications
controller of the situation. The TPJABB pin can source or sink
up to 10 mA, and so, is capable of driving a status LED. In the
AUI mode, the pin is driven to high impedance since the
transceiver connected to the AUI port must alert the
communications controller of the jabber condition.
Full Duplex
A feature unique to the MC68160, B and C is the Full
Duplex mode. In this mode the EEST is capable of
transmitting and receiving simultaneously. Collision
conditions are not announced and internal loop back is
disabled. The remainder of the EEST functionality remains
unchanged from the non–Full Duplex mode. Full Duplex
mode is enabled by asserting the TPFULDL pin.
Auto Port Selection
If the APORT pin is asserted, the MC68160, B and C will
automatically select the TP or AUI port depending on the
presence of valid link beats or frames at the TP RX+/– pins. If
the AUI port is automatically selected by another transmitting
station or by setting TPEN low, the TP transmit port of the
EEST continues to transmit link beats to keep the link active.
Auto Polarity Selection
If the RX+ and the RX– wires happen to get reversed, the
MC68160, B and C has the ability to automatically reverse the
pins internally so that the received data is valid. In addition, an
open collector status pin (TPPLR) is driven low to indicate the
fault. In the AUI or reset mode this pin presents a high
impedance.
Loop Back Mode
To test the transmit and receive circuitry without disturbing
the connected network, the EEST has a Loop Back mode.
Loop Back mode routes transmit data and clock to the
receive data and clock pins using as much of the transmit and
receive circuitry as possible. This gives a test of the
MC68160, B and C Manchester encode and decode function.
LOOP must not be asserted when TPFULDL pin is asserted.
This causes the MC68160, B and C to enter a test mode. This
test mode is used during final test and is not intended to be
entered under normal operation (see Application Notes
section).
相關PDF資料
PDF描述
MC68175 FLEXchip Decoder(FLEXchip譯碼器)
MC68176 2-bit A/D Converter(2位A/D轉換器)
MC68177 FLEXchip Decoder(FLEXchip譯碼器)
MC68181 Roaming FLEXchip(漫游式FLEX芯片)
MC68306 32-Bit Microprocessor(32位微處理器)
相關代理商/技術參數
參數描述
MC68181 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Advance Information ROAMING FLEX chip SIGNAL PROCESSOR
MC68184 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Broadband Interface Controller
MC68185 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:MC68185 Twisted-Pair Modem(TPM)
MC68194 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Carrier Band Modem(CBM)
MC68194FJ 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Carrier Band Modem(CBM)
主站蜘蛛池模板: 靖宇县| 永福县| 七台河市| 榆林市| 基隆市| 赤城县| 洪湖市| 桂林市| 财经| 朝阳县| 平江县| 宜州市| 牙克石市| 万年县| 文水县| 固阳县| 汨罗市| 涿州市| 夏邑县| 凤城市| 纳雍县| 山东| 德格县| 克拉玛依市| 千阳县| 同江市| 弋阳县| 莱芜市| 绥芬河市| 揭东县| 邯郸县| 云和县| 广安市| 台中市| 民丰县| 银川市| 曲靖市| 岑巩县| 五华县| 上犹县| 敦化市|