欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68341
廠商: Motorola, Inc.
英文描述: Integrated Processor Users Manual
中文描述: 綜合處理器用戶手冊
文件頁數: 5/21頁
文件大小: 134K
代理商: MC68341
MOTOROLA
MC68341 USER’S MANUAL ADDENDUM
4
6. Additional Notes on CPU Space Address Encoding
On page 3-31, Figure 3-16, the BKPT field for the Breakpoint Acknowledge address encoding is on bits 4-2,
and the T bit is on bit 1. The Interrupt Acknowledge LEVEL field is on bits 3-1.
7. Breakpoints
On page 3-31, the last paragraph implies that either a software breakpoint (BKPT instruction) or hardware
breakpoint can be used to insert an instruction. As noted in the following paragraphs, only a software
breakpoint can be used to insert an instruction on the breakpoint acknowledge cycle.
8. Interrupt Latency
Add to the Interrupt Acknowledge Bus Cycles section on page 3-36: Interrupt latency from IRQx assert to
prefetch of the first instruction in the interrupt handler is about 37 clocks + worst case instruction length in
clocks (using 2-clock memory and autovector termination). From the instruction timing tables, this gives 37+71
(DIVS.L with worst-case <fea>) = 108 clocks worst case interrupt latency time. For applications requiring
shorter interrupt response time the latency can be reduced by using simpler addressing modes and/or avoiding
use of longer instructions (specifically DIVS.L, DIVU.L, MUL.L).
9. Interrupt Hold Time and Spurious Interrupts
Add to the Interrupt Acknowledge Bus Cycles section on page 3-36: Level sensitive interrupts must remain
asserted until the corresponding IACK cycle; otherwise, a spurious interrupt exception may result or the inter-
rupt may be ignored entirely. This is also true for level sensitive external interrupts which are autovectored us-
ing either the AVEC signal or the AVEC register, since the SIM will not respond to an interrupt arbitration cycle
on the IMB if the external interrupt at that level has been removed. External interrupts configured as edge sen-
sitive only have to be held a minimum of 1.5 clocks - see section 4.3.5.8 PROGRAMMABLE INTERRUPT
REGISTER (PIR).
Note that the level 7 interrupt is also level sensitive, and must be held until a level 7 IACK begins. The level 7
interrupt is unique in that it cannot be masked - another level 7 interrupt exception can be created after the
IACK cycle by negating IRQ7 and reasserting, even though the interrupt mask level in the SR is now set to
level 7.
10. Typos in IACK Cycle Timing Waveforms
On page 3-38, Figure 3-21, the text “VECTOR FROM 16-BIT PORT” should be on D7-D0, and “VECTOR
FROM 8-BIT PORT” should be on D15-D8. The responding device returns the vector number on the least sig-
nificant byte of the data port.
11. Additional Note on Internal Autovector Operation
Add to the Autovector Interrupt Acknowledge Cycle section on page 3-38: If an external interrupt level is
autovectored either by the AVEC register programming or the external AVEC signal, an external IACK will be
started and terminated internally. The interrupting device should not respond to this IACK in any way, or the
resulting operation is undefined.
12. Additional Notes on Retry Termination
On page 3-42, Table 3-4: When HALT and BERR are asserted together in case #5 to force a retry of the current
bus cycle, relative timing of HALT and BERR must be controlled to avoid inadvertently causing bus error ter-
相關PDF資料
PDF描述
MC6835 8-BIT MPUS, 8-BIT MCUS, 8-BIT PERIPHERALS
MC6843 8-BIT MPUS, 8-BIT MCUS, 8-BIT PERIPHERALS
MC6844 8-BIT MPUS, 8-BIT MCUS, 8-BIT PERIPHERALS
MC6846 8-BIT MPUS, 8-BIT MCUS, 8-BIT PERIPHERALS
MC6852 8-BIT MPUS, 8-BIT MCUS, 8-BIT PERIPHERALS
相關代理商/技術參數
參數描述
MC68341FT16 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Integrated Processor Users Manual
MC68341FT16V 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Integrated Processor Users Manual
MC68341FT25 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Integrated Processor Users Manual
MC68341UMAD 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Integrated Processor Users Manual
MC68349 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HIGH PERFORMANCE INTEGRATED PROCESSOR
主站蜘蛛池模板: 贵阳市| 海安县| 和龙市| 孟连| 南漳县| 清远市| 沙坪坝区| 安图县| 晋州市| 门源| 花垣县| 项城市| 繁昌县| 太仆寺旗| 顺昌县| 松溪县| 道孚县| 亳州市| 莎车县| 五华县| 泽普县| 江西省| 钦州市| 玉树县| 开封县| 钟祥市| 桂平市| 内乡县| 江津市| 三亚市| 兴义市| 昭通市| 永平县| 饶河县| 平遥县| 六枝特区| 靖西县| 蛟河市| 尼玛县| 崇明县| 竹北市|