欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68HCL05C9A
廠商: Motorola, Inc.
元件分類: 8位微控制器
英文描述: 8-Bit Microcontroller(8位微控制器)
中文描述: 8位微控制器(8位微控制器)
文件頁數: 92/160頁
文件大小: 783K
代理商: MC68HCL05C9A
L
G
R
Serial Peripheral Interface
General Release Specification
MC68HC05C9A
Rev. 4.0
92
Serial Peripheral Interface
MOTOROLA
10.4.3 Serial Clock (SCK)
The master clock is used to synchronize data movement both in and out
of the device through its MOSI and MISO lines. The master and slave
devices are capable of exchanging a byte of information during a
sequence of eight clock cycles. Since SCK is generated by the master
device, this line becomes an input on a slave device.
As shown in
Figure 10-1
, four possible timing relationships may be
chosen by using control bits CPOL and CPHA in the serial peripheral
control register (SPCR). Both master and slave devices must operate
with the same timing. The master device always places data on the
MOSI line a half cycle before the clock edge (SCK), in order for the slave
device to latch the data.
Two bits (SPR0 and SPR1) in the SPCR of the master device select the
clock rate. In a slave device, SPR0 and SPR1 have no effect on the
operation of the SPI.
10.4.4 Slave Select (SS)
The slave select (SS) input line is used to select a slave device. It has to
be low prior to data transactions and must stay low for the duration of the
transaction.The SS line on the master must be tied high. In master
mode, if theSS pin is pulled low during a transmission, a mode fault error
flag (MODF) is set in the SPSR. In master mode the SS pin can be
selected to be a general-purpose output by writing a one in bit 5 of the
port D data direction register, thus disabling the mode fault circuit.
When CPHA = 0, the shift clock is the OR of SS with SCK. In this clock
phase mode, SS must go high between successive characters in an SPI
message. When CPHA = 1, SS may be left low for several SPI
characters. In cases where there is only one SPI slave MCU, its SS line
could be tied to V
SS
as long as CPHA = 1 clock modes are used.
相關PDF資料
PDF描述
MC68HSC05C9A 8-Bit Microcontroller(8位微控制器)
MC68HC05F2 8-Bit Microcontroller Units (MCU).(8位微控制器)
MC68HC05F6 8-Bit Microcontroller Units (MCU).(8位微控制器)
MC68HC05K3 8-Bit Microcontroller Units (MCU).(8位微控制器)
MC68HC805K3 8-Bit Microcontroller Units (MCU).(8位微控制器)
相關代理商/技術參數
參數描述
MC68HCP11A1CFN3 功能描述:8位微控制器 -MCU 8-bit HCMOS single chip MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HCP11A1FN 制造商:MOTORALA 功能描述:
MC68HCP11E0CP2 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HCP11E0FN 功能描述:MICROCONTROLLER MCU 8ADC 3MHC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:HC11 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN,SCI,SPI 外圍設備:POR,PWM,溫度傳感器,WDT 輸入/輸出數:21 程序存儲器容量:40KB(20K x 16) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
MC68HCP11E0FNE 功能描述:8位微控制器 -MCU 8B MCU 512RAM COP A/D RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
主站蜘蛛池模板: 岗巴县| 鄂伦春自治旗| 江孜县| 庆安县| 延津县| 平果县| 贺州市| 全南县| 微博| 扎鲁特旗| 大埔区| 潜江市| 前郭尔| 伊吾县| 颍上县| 台南市| 河津市| 上虞市| 共和县| 乳源| 英超| 富顺县| 鸡西市| 揭西县| 开远市| 当雄县| 邢台市| 闻喜县| 泽普县| 新平| 浪卡子县| 台山市| 凌源市| 扎鲁特旗| 清原| 淄博市| 漠河县| 海南省| 永春县| 祁连县| 东至县|