- 您現在的位置：買賣IC網 > Datasheet目錄44 > MCP9808T-E/MS (Microchip Technology)IC TEMP SENSOR DGTL I2C 8MSOP Datasheet資料下載
參數資料
| 型號： | MCP9808T-E/MS |
| 廠商： | Microchip Technology |
| 文件頁數： | 13/52頁 |
| 文件大小： | 1085K |
| 描述： | IC TEMP SENSOR DGTL I2C 8MSOP |
| 標準包裝： | 2,500 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部 |
| 感應溫度： | -40°C ~ 125°C |
| 精確度： | ±1°C |
| 拓撲： | ADC（三角積分型），寄存器庫 |
| 輸出類型： | 2 線串行，I²C?/SMBUS? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-MSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
?2011 Microchip Technology Inc.
DS25095A-page 13
MCP9808
4.0
SERIAL COMMUNICATION
4.1
2-Wire Standard Mode I
2
C"
Protocol Compatible Interface
The MCP9808 Serial Clock (SCL) input and the
bidirectional Serial Data (SDA) line form a 2-wire
bidirectional, Standard mode, I
2
C compatible
communication port (refer to the Digital Input/Output
Pin Characteristics and Sensor Serial Interface
Timing Specifications tables).
The following bus protocol has been defined:
4.1.1
DATA TRANSFER
Data transfers are initiated by a Start condition
(START), followed by a 7-bit device address and a
read/write bit. An Acknowledge (ACK) from the slave
confirms the reception of each byte. Each access must
be terminated by a Stop condition (STOP).
Repeated communication is initiated after t
B-FREE
.
This device does not support sequential register
read/write. Each register needs to be addressed using
the Register Pointer.
This device supports the receive protocol. The register
can be specified using the pointer for the initial read.
Each repeated read or receive begins with a Start
condition and address byte. The MCP9808 retains the
previously selected register. Therefore, it outputs data
from the previously specified register (repeated pointer
specification is not necessary).
4.1.2
MASTER/SLAVE
The bus is controlled by a master device (typically a
microcontroller) that controls the bus access and
generates the Start and Stop conditions. The MCP9808
is a slave device and does not control other devices in
the bus. Both master and slave devices can operate as
either transmitter or receiver. However, the master
device determines which mode is activated.
4.1.3
START/STOP CONDITION
A high-to-low transition of the SDA line (while SCL is
high) is the Start condition. All data transfers must be
preceded by a Start condition from the master. A
low-to-high transition of the SDA line (while SCL is
high) signifies a Stop condition.
If a Start or Stop condition is introduced during data
transmission, the MCP9808 releases the bus. All data
transfers are ended by a Stop condition from the
master.
TABLE 4-1:
MCP9808 SERIAL BUS
PROTOCOL DESCRIPTIONS
Term
Description
Master
The device that controls the serial bus,
typically a microcontroller.
Slave
The device addressed by the master,
such as the MCP9808.
Transmitter Device sending data to the bus.
Receiver
Device receiving data from the bus.
START
A unique signal from the master to
initiate serial interface with a slave.
STOP
A unique signal from the master to
terminate serial interface from a slave.
Read/Write A read or write to the MCP9808
registers.
ACK
A receiver Acknowledges (ACK) the
reception of each byte by polling the bus.
NAK
A receiver Not-Acknowledges (NAK) or
releases the bus to show End-of-Data
(EOD).
Busy
Communication is not possible
because the bus is in use.
Not Busy
The bus is in the Idle state; both SDA
and SCL remain high.
Data Valid SDA must remain stable before SCL
becomes high in order for a data bit to
be considered valid. During normal
data transfers, SDA only changes state
while SCL is low.
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33998EGR2 | IC REG CHARGEPUMP/LINEAR 24SOIC |
| MCZ34652EFR2 | IC HOTSWAP CTRLR 2A NEG 16SOIC |
| MCZ34653EFR2 | IC HOTSWAP CTRLR 1A NEG 8-SOIC |
| MCZ34670EG | IC POE CURR MODE SW REG 20-SOIC |
| MIC184BM TR | IC SUPERVISOR LOCAL/REMOTE 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP98242 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Memory Module Temperature Sensor w/EEPROM for SPD |
| MCP98242_09 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Memory Module Temperature Sensor w/EEPROM for SPD |
| MCP98242-BE/MC | 制造商:Microchip Technology Inc 功能描述:TEMP SENSOR DGTL SERL (2-WIRE, - Bulk |
| MCP98242-BE/MNY | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Memory Module Temperature Sensor w/EEPROM for SPD |
| MCP98242-BE/ST | 功能描述:板上安裝溫度傳感器 JEDEC DIMM Serial output temp sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。