- 您現在的位置：買賣IC網 > Datasheet目錄44 > MCP9808T-E/MS (Microchip Technology)IC TEMP SENSOR DGTL I2C 8MSOP Datasheet資料下載
參數資料
| 型號： | MCP9808T-E/MS |
| 廠商： | Microchip Technology |
| 文件頁數： | 14/52頁 |
| 文件大?。?/td> | 1085K |
| 描述： | IC TEMP SENSOR DGTL I2C 8MSOP |
| 標準包裝： | 2,500 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部 |
| 感應溫度： | -40°C ~ 125°C |
| 精確度： | ±1°C |
| 拓撲： | ADC（三角積分型），寄存器庫 |
| 輸出類型： | 2 線串行，I²C?/SMBUS? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-MSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
MCP9808
DS25095A-page 14
?2011 Microchip Technology Inc.
4.1.4
ADDRESS BYTE
Following the Start condition, the host must transmit an
8-bit address byte to the MCP9808. The address for the
MCP9808 temperature sensor is 0011,A2,A1,A0 in
binary, where the A2, A1 and A0 bits are set externally
by connecting the corresponding pins to V
DD
1 or GND
0. The 7-bit address, transmitted in the serial bit stream,
must match the selected address for the MCP9808 to
respond with an ACK. Bit 8 in the address byte is a
read/write bit. Setting this bit to 1 commands a read
operation, while 0 commands a write operation (see
Figure 4-1).
FIGURE 4-1:
Device Addressing.
4.1.5
DATA VALID
After the Start condition, each bit of data in the
transmission needs to be settled for a time specified by
t
SU-DATA
before SCL toggles from low-to-high (see the
Sensor Serial Interface Timing Specifications section).
4.1.6
ACKNOWLEDGE (ACK/NAK)
Each receiving device, when addressed, must
generate an ACK bit after the reception of each byte.
The master device must generate an extra clock pulse
for ACK to be recognized.
The Acknowledging device pulls down the SDA line for
t
SU-DATA
before the low-to-high transition of SCL from
the master. SDA also needs to remain pulled down for
t
H-DATA
after a high-to-low transition of SCL.
During read, the master must signal an End-of-Data
(EOD) to the slave, by not generating an ACK bit
(NAK), once the last bit has been clocked out of the
slave. In this case, the slave will leave the data line
released to enable the master to generate the Stop
condition.
4.1.7
TIME-OUT
If the SCL stays low or high for the time specified by
t
OUT
, the MCP9808 temperature sensor resets the
serial interface. This dictates the minimum clock speed
as outlined in the specification.
1 2 3 4 5 6 7 8 9
SCL
SDA
0 1 1 A2 A1 A0
Start
Address Byte
Slave
Address
R/W
MCP9808 Response
Code
Address
A
C
K
0
See Table 3-2.
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33998EGR2 | IC REG CHARGEPUMP/LINEAR 24SOIC |
| MCZ34652EFR2 | IC HOTSWAP CTRLR 2A NEG 16SOIC |
| MCZ34653EFR2 | IC HOTSWAP CTRLR 1A NEG 8-SOIC |
| MCZ34670EG | IC POE CURR MODE SW REG 20-SOIC |
| MIC184BM TR | IC SUPERVISOR LOCAL/REMOTE 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP98242 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Memory Module Temperature Sensor w/EEPROM for SPD |
| MCP98242_09 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Memory Module Temperature Sensor w/EEPROM for SPD |
| MCP98242-BE/MC | 制造商:Microchip Technology Inc 功能描述:TEMP SENSOR DGTL SERL (2-WIRE, - Bulk |
| MCP98242-BE/MNY | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Memory Module Temperature Sensor w/EEPROM for SPD |
| MCP98242-BE/ST | 功能描述:板上安裝溫度傳感器 JEDEC DIMM Serial output temp sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。