- 您現在的位置：買賣IC網 > PDF目錄16759 > MCZ33742EG (Freescale Semiconductor)IC SYSTEM BASIS CHIP CAN 28-SOIC PDF資料下載
參數資料
| 型號： | MCZ33742EG |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 15/71頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SYSTEM BASIS CHIP CAN 28-SOIC |
| 標準包裝： | 26 |
| 應用： | 自動 |
| 電流 - 電源： | 42mA |
| 電源電壓： | 5.5 V ~ 18 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 28-SOIC W |
| 包裝： | 管件 |
| 產品目錄頁面： | 808 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁
Analog Integrated Circuit Device Data
22
Freescale Semiconductor
33742
FUNCTIONAL DESCRIPTION
INTRODUCTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
The 33742 and the 33742S are system basis chips (SBCs) dedicated to automotive applications. Their functions include the
following:
One fully protected 5.0 V voltage regulator with 200 mA total output current capability available at the VDD pin.
VDD regulator under-voltage reset function, programmable window or time-out software watchdog function.
Internal driver (V2) for an external series pass transistor to implement a second 5.0 V voltage regulator.
Two running modes: Normal and Standby modes set by the system microcontroller.
Sleep and Stop modes low power operating modes to reduce an application’s current consumption while providing a wake-
up capability from the CAN interface, L3:L0 wake-up inputs, or from a timer wake-up.
Programmable wake-up input and cyclic sense wake-ups.
CAN high-speed physical bus interface with TXD and RXD fault diagnostic capability and enhanced protection features.
An SPI interface for use in communicating with a MCU and Interrupt outputs to report SBC status, perform diagnostics, and
report wake-up events.
FUNCTIONAL PIN DESCRIPTION
RECEIVE AND TRANSMIT DATA (RXD AND TXD)
The RXD and TXD pins (receive data and transmit data pins, respectively) are connected to a microcontroller’s CAN protocol
handler. TXD is an input and controls the CANH and CANL line state (dominant when TXD is LOW, recessive when TXD is
HIGH). RXD is an output and reports the bus state (RXD LOW when CAN bus is dominant, HIGH when CAN bus is recessive).
The RXD terminal is a push-pull structure between the V2 pin and GND.
Voltage Digital Drain (VDD)
The VDD pin is the output pin of the 5.0 V internal regulator. It can deliver up to 200 mA. This output is protected against over-
current and over-temperature. It includes an over-temperature pre-warning flag, which is set when the internal regulator
temperature exceeds 130 °C typical. When the temperature exceeds the over-temperature shutdown (170 °C typical), the
regulator is turned off.
VDD includes an under-voltage reset circuitry, which sets the RST pin LOW when VDD is below the under-voltage reset
threshold.
RESET OUTPUT (RST)
The RESET pin RST, is an output that is set LOW when the device is in reset mode. The RST pin is set HIGH when the device
is not in reset mode. RST includes an internal pull-up current source. When RST is LOW, the sink current capability is limited,
allowing RST to be shorted to 5.0 V for software debug or software download purposes.
INTERRUPT OUTPUT (INT)
The Interrupt pin INT, is an output that is set LOW when an interrupt occurs. INT is enabled using the Interrupt Register (INTR).
When an interrupt occurs, INT stays LOW until the interrupt source is cleared.
INT output also reports a wake-up event by a 10
s typical pulse when the device is in Stop mode.
VOLTAGE SOURCE 2 (V2)
The V2 pin is the input sense for the V2 regulator. It is connected to the external series pass transistor. V2 is also the 5.0 V
supply of the internal CAN interface. It is possible to connect V2 to an external 5.0 V regulator or to the VDD output when no
external series pass transistor is used. In this case, the V2CTRL pin must be left open. Refer to Figure 31, SBC Typical
VOLTAGE SOURCE 2 CONTROL (V2CTRL)
The V2CTRL pin is the output drive pin for the V2 regulator connected to the external series pass transistor.
相關PDF資料 |
PDF描述 |
|---|---|
| H2MXH-1618M | DIP CABLE - HDM16H/AE16M/X |
| PCK0G331MCO1GS | CAP ALUM 330UF 4V 20% SMD |
| SDR0805-681KL | INDUCTOR POWER 680UH 10% SMD |
| AD587JR-REEL | IC VREF SERIES PREC 10V 8-SOIC |
| B82422A3151K100 | INDUCTOR .15UH 390MA 1210 10% |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33742EGR2 | 功能描述:網絡控制器與處理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCZ33742SEG | 功能描述:網絡控制器與處理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCZ33742SEGR2 | 功能描述:網絡控制器與處理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCZ33780EG | 功能描述:多路器開關 IC DBUS MASTER RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MCZ33780EG | 制造商:Freescale Semiconductor 功能描述:DUAL DBUS MASTER INTERFACE 16SOIC |
發布緊急采購，3分鐘左右您將得到回復。