- 您現在的位置：買賣IC網 > PDF目錄16759 > MCZ33742EG (Freescale Semiconductor)IC SYSTEM BASIS CHIP CAN 28-SOIC PDF資料下載
參數資料
| 型號： | MCZ33742EG |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 22/71頁 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM BASIS CHIP CAN 28-SOIC |
| 標準包裝： | 26 |
| 應用： | 自動 |
| 電流 - 電源： | 42mA |
| 電源電壓： | 5.5 V ~ 18 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 28-SOIC W |
| 包裝： | 管件 |
| 產品目錄頁面： | 808 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
29
33742
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
APPLICATION WAKE-UP FROM THE MCU
When the device is in the Stop mode, a wake-up event may come from the system MCU. In this case the MCU selects the
device the using a LOW-to-HIGH transition on the 33742 CS pin. Then the 33742S goes into Normal Request mode and
generates an interrupt pulse at the INT pin.
STOP MODE CURRENT MONITOR
If the VDD output current exceeds an internal set threshold (IDDS-WU), the SBC automatically enters the Normal Request mode
and generates an interrupt at the INT pin. The interrupt is a non-maskable and the INTR register will have no flag set.
INTERRUPT GENERATION WHEN WAKE-UP FROM STOP MODE
When the SBC wakes from Stop mode, it first enters the Normal Request mode before generating a 10
s typical pulse on the
INT pin. These are non-maskable interrupts with the wake-up event read through the SPI registers, the CANWU bit in the CAN
Register (CANR), or the LCTRx bit in the Wake-up Register (WUR). In case of wake-up from Stop mode over-current situation
or from forced wake-up, no bits are set. After the INT pulse, the 33742 accepts SPI command after a time delay (tS-1STSPI).
WATCHDOG SOFTWARE IN STOP MODE
If the SBC watchdog is enabled, the application must provide a “system ok” response before the end of the 33742 watchdog
time. Typically an MCU initiates the wake-up of the 33742 through the SPI wake-up (CS activation). The SBC will awaken and
jump into the Normal Request mode. The MCU has to configure the 33742 to go to either Normal or Standby mode. The MCU
can then decide to return to the Stop mode.
If no MCU wake-up occurs within the watchdog time period, the SBC activates the RST pin and jumps into the Normal Request
mode. The MCU can then be re-initialized.
STOP MODE ENTER COMMAND
Stop mode is entered at the end of the SPI message at the rising edge of the CS. (Refer to the t CS-STOP data in the Dynamic
Electrical Characteristics table on page 16.) Once Stop mode is entered, the SBC can wake up from a VDD regulator over-current
detection state. In order to allow time for the MCU to complete the last CPU instruction and enter its low power mode, a deglitcher
time of 40
s typical is implemented.
Figure 11. Entering the Stop Mode
WATCHDOG SOFTWARE (RST AND WDOG)(SELECTABLE WATCHDOG WINDOW
OR WATCHDOG TIME-OUT)
A watchdog is used in the SBC Normal and Standby modes for monitoring the MCU operation. The watchdog timer may be
implemented as either a watchdog window or watchdog timeout, selectable by SPI (TIM1 sub register, bit WDW). Default
operation is a watchdog window.
The watchdog period can be set from 10 to 350 ms (TIM1 sub register, bits WDT0 and WDT1). When a watchdog window is
selected, the closed window is the first part of the selected period, and the open window is the second part of the period. (Refer
to Timing Register (TIM1/2) beginning on page 52.)
The watchdog can only be cleared within the open window time period. Any attempt to clear watchdog in the closed window
will generate a reset. The watchdog is cleared addressing the TIM1 sub register using the SPI
SPI CS
SPI Stop/Sleep
Command
33742 in Normal
or Standby mode
33742 in Stop mode.
No IDD over IDD-DGLT
33742 in Stop mode.
IDD over IDD-DGLT
tCS-STOP
tIDD-DGLT
相關PDF資料 |
PDF描述 |
|---|---|
| H2MXH-1618M | DIP CABLE - HDM16H/AE16M/X |
| PCK0G331MCO1GS | CAP ALUM 330UF 4V 20% SMD |
| SDR0805-681KL | INDUCTOR POWER 680UH 10% SMD |
| AD587JR-REEL | IC VREF SERIES PREC 10V 8-SOIC |
| B82422A3151K100 | INDUCTOR .15UH 390MA 1210 10% |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33742EGR2 | 功能描述:網絡控制器與處理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCZ33742SEG | 功能描述:網絡控制器與處理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCZ33742SEGR2 | 功能描述:網絡控制器與處理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCZ33780EG | 功能描述:多路器開關 IC DBUS MASTER RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MCZ33780EG | 制造商:Freescale Semiconductor 功能描述:DUAL DBUS MASTER INTERFACE 16SOIC |
發布緊急采購，3分鐘左右您將得到回復。