- 您現在的位置：買賣IC網 > PDF目錄382356 > N643GT7GI (Advanced Micro Devices, Inc.) 64 Megabit (4 M x 16-Bit) CMOS 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory PDF資料下載
參數資料
| 型號： | N643GT7GI |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | 64 Megabit (4 M x 16-Bit) CMOS 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory |
| 中文描述： | 64兆位（4個M x 16位）的CMOS 1.8伏，只有同時讀/寫，突發模式閃存 |
| 文件頁數： | 29/49頁 |
| 文件大小： | 382K |
| 代理商： | N643GT7GI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
May 8, 2006 25692A2
Am29BDS643G
27
D A T A S H E E T
RDY: Ready
The RDY is a dedicated output that indicates (when at
logic low) the system should wait until RDY returns high
before expecting the next word of data.
RDY functions only while reading data in burst mode.
The following conditions cause the RDY output to be
low: during the initial access (in burst mode); after the
boundary that occurs every 64 words beginning with
the 63rd address, 3Eh; and when the clock frequency
is less than 6 MHz (in which case RDY is low every third
clock). The RDY pin will also switch during status reads
if there is a clock signal at the CLK input. If RDY goes
low, it indicates that the status data is not yet valid and
that the system should wait until RDY returns high.
DQ6: Toggle Bit I
Toggle Bit I on DQ6 indicates whether an Embedded
Program or Erase algorithm is in progress or complete,
or whether the device has entered the Erase Suspend
mode. Toggle Bit I may be read at any address in the
same bank, and is valid after the rising edge of the final
WE# pulse in the command sequence (prior to the
program or erase operation), and during the sector
erase time-out.
During an Embedded Program or Erase algorithm
operation, successive read cycles to any address
cause DQ6 to toggle. Note that OE# must be low during
toggle bit status reads. When the operation is com-
plete, DQ6 stops toggling.
After an erase command sequence is written, if all
sectors selected for erasing are protected, DQ6 toggles
for approximately 100 μs, then returns to reading array
data. If not all selected sectors are protected, the
Embedded Erase algorithm erases the unprotected
sectors, and ignores the selected sectors that are pro-
tected.
The system can use DQ6 and DQ2 together to deter-
mine whether a sector is actively erasing or is
erase-suspended. When the device is actively erasing
(that is, the Embedded Erase algorithm is in progress),
DQ6 toggles. When the device enters the Erase
Suspend mode, DQ6 stops toggling. However, the
system must also use DQ2 to determine which sectors
are erasing or erase-suspended. Alternatively, the
system can use DQ7 (see the subsection on DQ7:
Data# Polling).
If a program address falls within a protected sector,
DQ6 toggles for approximately 1
μ
s after the program
command sequence is written, then returns to reading
array data.
DQ6 also toggles during the erase-suspend-program
mode, and stops toggling once the Embedded
Program algorithm is complete.
See the following for additional information: Figure 4
(toggle bit flowchart), DQ6: Toggle Bit I (description),
Figure 17 (toggle bit timing diagram), and Table 11
(compares DQ2 and DQ6).
Figure 4.
Toggle Bit Algorithm
START
No
Yes
Yes
DQ5 = 1
No
Yes
DQ6 = Toggle
No
Read Byte
(DQ0-DQ7)
Address = VA
DQ6 = Toggle
Read Byte Twice
(DQ 0-DQ7)
Adrdess = VA
Read Byte
(DQ0-DQ7)
Address = VA
FAIL
PASS
Note:
The system should recheck the toggle bit even if DQ5
= “1” because the toggle bit may stop toggling as DQ5
changes to “1.” See the subsections on DQ6 and DQ2 for
more information.
相關PDF資料 |
PDF描述 |
|---|---|
| N643GT7MI | 64 Megabit (4 M x 16-Bit) CMOS 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory |
| N80186 | High Integration 16-Bit Microprocessor iAPX86 Family |
| N80186-10 | High Integration 16-Bit Microprocessor iAPX86 Family |
| N80186-10B | High Integration 16-Bit Microprocessor iAPX86 Family |
| N80186B | High Integration 16-Bit Microprocessor iAPX86 Family |
相關代理商/技術參數 |
參數描述 |
|---|---|
| N643GT7MI | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:64 Megabit (4 M x 16-Bit) CMOS 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory |
| N6455A | 制造商:Agilent Technologies 功能描述:HARD COPY MANUAL, 4000X-SERIES OSCILLOSCOPE; Plug Type:-; Accessory Type:Hard Copy Manual; For Use With:InfiniiVision 4000 X-Series Oscilloscopes ;RoHS Compliant: NA |
| N6456A | 制造商:AGILENT TECHNOLOGIES, INC. 功能描述:Rackmount Kit for 2000 and 3000X Series Oscilloscopes 制造商:Agilent Technologies 功能描述:Bulk 制造商:Agilent Technologies 功能描述:OPTION RACK MOUNT KIT FOR X-SERIES 制造商:Agilent Technologies 功能描述:RACK MOUNT KIT; Accessory Type:Rackmount Kit; For Use With:Agilent InfiniiVision 2000X / 3000X Series Oscilloscopes ;RoHS Compliant: NA 制造商:Agilent Technologies 功能描述:Rack mount kit |
| N6457A | 制造商:AGILENT TECHNOLOGIES, INC. 功能描述:Soft Carrying Case and Front Panel Cover for 2000 and 3000X Series Scopes 制造商:Agilent Technologies 功能描述:Bulk 制造商:Agilent Technologies 功能描述:ACCESSORY SOFT CASE AND FRONT PANEL 制造商:Agilent Technologies 功能描述:ACCESSORY, SOFT CASE AND FRONT PANEL 制造商:Agilent Technologies 功能描述:SOFT CARRYING CASE AND FRONT PANEL COVER; Accessory Type:Case and Front Panel Cover; For Use With:Agilent InfiniiVision 2000X / 3000X Series Oscilloscopes ;RoHS Compliant: NA 制造商:Agilent Technologies 功能描述:Soft Carrying Case |
| N6458A-ABA | 制造商:Agilent Technologies 功能描述:Hard Copy User's Manual 2000 X series 制造商:Agilent Technologies 功能描述:N6458A / English Users Guide |
發布緊急采購，3分鐘左右您將得到回復。