- 您現在的位置：買賣IC網 > PDF目錄361089 > NCN6000 (ON SEMICONDUCTOR) Compact Smart Card Interface IC(智能卡接口集成電路) PDF資料下載
參數資料
| 型號： | NCN6000 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | Compact Smart Card Interface IC(智能卡接口集成電路) |
| 中文描述： | 緊湊型智能卡接口IC（智能卡接口集成電路） |
| 文件頁數： | 15/36頁 |
| 文件大小： | 358K |
| 代理商： | NCN6000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
NCN6000
http://onsemi.com
15
Basic Operating Modes Flow Chart
The NCN6000 brings all the functions necessary to handle
data communication between a host computer and the smart
card. The builtin Chip Select pin provides a simple way to
share the same MPU bus with several card interface. On top
of that, the logic control are derived from specific pins,
avoiding the risk of mixing up the operation when the
interface is controlled by a low end microcontroller.
During the transaction operation, the external MPU takes
care of whatever is necessary to he data on the single
bidirectional I/O line. Leaving aside the DCDC control and
associated failures, the NCN6000 does not take any further
responsibility in the data transaction.
When the chip operates in the programming mode, the
NCN6000 provide a flexible access to set up the CRD_VCC
voltage, the CRD_CLK and the CRD_DET smart card
signals.
The external microcontroller takes care of the smart card
transaction and shall handle the interface accordingly.
Figure 7. Operating Modes Flow Chart
RESET
Vbat = OK
STAND BY MODE
CS = H
PGM = H
SELECT OPERATING MODE
CS = H
PROGRAMMING
MODE
SET NCN6000
PARAMETERS
ACTIVE MODE
PWR_ON = H
SEND ATR SEQUENCE
TRANSACTION MODE
END MODE
POWER DOWN SEQUENCE
IDLE MODE
FINISH
PGM = L
CS = L
PGM = H
CS = L
LATCH NCN6000
PARAMETERS
PGM = H
CS = H
Standby Mode
The Standby Mode allows the NCN6000 to detect a card
insertion, keeping the power consumption at a minimum.
The power supply CRD_VCC is not applied to the card, until
the external controllers set PWR_ON = H with CS = L.
Standby Mode
Logic Conditions:
Card Output:
CS
PWR_ON = H
A0
A1
PGM
I/O
RESET
= H
= Z
= Z
= Z
= Z
= Z
CRD_VCC = 0 V
CRD_CLK = L
CRD_RST = L
CRD_IO
= L
When a card is inserted, the internal logic filters the signal
present pin 11, then asserts the INT pin to Low if the pulse
applied to CRD_DET is longer than 150 s. The external
MPU shall run whatever is necessary to handle the card.
The INT is cleared (return to High) when a positive going
transition is asserted to either the CS or to the PWR_ON
signal logically combined with Chip Select = Low.
相關PDF資料 |
PDF描述 |
|---|---|
| NCN6001DTBR2 | Compact Smart Card Interface IC |
| NCN6001 | Compact Smart Card Interface IC |
| NCN6004AFTBR2 | Dual SAM/SIM Interface Integrated Circuit |
| NCN6004A | Dual SAM/SIM Interface Integrated Circuit |
| NCN6010DTBR2 | SIM Card Supply and Level Shifter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCN6000/D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Compact Smart Card Interface IC |
| NCN6000DTB | 功能描述:輸入/輸出控制器接口集成電路 2.7V POS/ATM Smart RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| NCN6000DTBG | 功能描述:輸入/輸出控制器接口集成電路 2.7V POS/ATM Smart Card Interface RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| NCN6000DTBR2 | 功能描述:輸入/輸出控制器接口集成電路 2.7V POS/ATM Smart RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| NCN6000DTBR2G | 功能描述:輸入/輸出控制器接口集成電路 2.7V POS/ATM Smart Card Interface RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。