- 您現在的位置：買賣IC網 > PDF目錄361089 > NCN6000 (ON SEMICONDUCTOR) Compact Smart Card Interface IC(智能卡接口集成電路) PDF資料下載
參數資料
| 型號： | NCN6000 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | Compact Smart Card Interface IC(智能卡接口集成電路) |
| 中文描述： | 緊湊型智能卡接口IC（智能卡接口集成電路） |
| 文件頁數： | 5/36頁 |
| 文件大小： | 358K |
| 代理商： | NCN6000 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
NCN6000
http://onsemi.com
5
The programming can be achieved with the card powered
ON or OFF. The identification of the interrupt is carried out
by polling the STATUS pin, the Vbat voltage and the
DCDC results being provided on the same pin as depicted
by the table in Figure 4. During the programming mode, the
PGM pin can be released to High since the mode is internally
latched by the Negative going transition presents on the Chip
Select pin.
PGM
INT
CRD_DET
CARD EXTRACTED
CARD IDENTIFICATION
POLLING
50 s
INTERRUPT
ACKNOWLEDGE
50 s
High
Low
Low
CS
A0
A1
STATUS
S1 CLEAR INTERRUPT
S2 CARD PRESENT: STATUS = 1
S3 CLEAR INTERRUPT
S4 CARD PRESENT: STATUS = 0
Figure 5. Interrupt Servicing and Card Polling
When a card is either inserted or extracted, the CRD_DET
pin signal is debounced internally prior to pull the INT pin
to Low. The builtin logic circuit automatically
accommodates positive or negative input signal slope, on
both insertion and extraction state, depending upon the
polarity defined during the initialization sequence. The
default condition is Normally Open switch, negative going
card detection. The external CPU shall acknowledge the
request by forcing CS = L which, in turn, releases the INT
pin to High upon positive going of Chip Select (Table 4).
Polling the STATUS pin as depicted in Table 3 identifies the
active card. If a card is present, the STATUS returns High,
otherwise a Low is presented pin 5. The 50 s digital filter
is activated during both Insertion and Extraction of the card.
The MPU shall clear the INT line when the card has been
extracted, making the interrupt function available for other
purposes. However, neither the NCN6000 operation nor the
smart card I/O line or commands are affected by the state of
the INT pin.
On the other hand, clearing the INT and reading the
STATUS register can be performed by a single read by the
MPU: states S1 and S2 can be combined in a single
instruction, the same for S3 and S4.
相關PDF資料 |
PDF描述 |
|---|---|
| NCN6001DTBR2 | Compact Smart Card Interface IC |
| NCN6001 | Compact Smart Card Interface IC |
| NCN6004AFTBR2 | Dual SAM/SIM Interface Integrated Circuit |
| NCN6004A | Dual SAM/SIM Interface Integrated Circuit |
| NCN6010DTBR2 | SIM Card Supply and Level Shifter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCN6000/D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Compact Smart Card Interface IC |
| NCN6000DTB | 功能描述:輸入/輸出控制器接口集成電路 2.7V POS/ATM Smart RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| NCN6000DTBG | 功能描述:輸入/輸出控制器接口集成電路 2.7V POS/ATM Smart Card Interface RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| NCN6000DTBR2 | 功能描述:輸入/輸出控制器接口集成電路 2.7V POS/ATM Smart RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| NCN6000DTBR2G | 功能描述:輸入/輸出控制器接口集成電路 2.7V POS/ATM Smart Card Interface RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。