- 您現在的位置：買賣IC網 > Datasheet目錄45 > NCT75MNR2G (ON Semiconductor)IC SENSOR TEMP DGTL 8DFN Datasheet資料下載
參數資料
| 型號： | NCT75MNR2G |
| 廠商： | ON Semiconductor |
| 文件頁數： | 11/15頁 |
| 文件大小： | 181K |
| 描述： | IC SENSOR TEMP DGTL 8DFN |
| 標準包裝： | 3,000 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部 |
| 感應溫度： | -55°C ~ 125°C |
| 精確度： | ±3°C |
| 拓撲： | ADC（三角積分型），控制邏輯，寄存器庫 |
| 輸出類型： | 2 線串行，I²C?/SMBUS? |
| 輸出警報： | 是 |
| 輸出風扇： | 無 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-VFDFN 裸露焊盤 |
| 供應商設備封裝： | 8-DFN（2x2） |
| 包裝： | 帶卷 (TR) |
NCT75
http://onsemi.com
11
Reading Data
Reading data from the NCT75 is done in two different
ways depending on the register being read. The
configuration register is only 8 bits wide so a single byte
read is used for this (shown in Figure 8). This consists of the
device address followed by the data from the register.
Reading the data in the temperature value register requires
a two byte read (shown in Figure 9). This consists of the
device address, followed by two bytes of data from the
temperature register (the first byte is the MSB). In both cases
the address pointer register of the register being read must
be written to prior to performing a read operation.
OS
/ALERT
Output Overtemperature Modes
The OS
/ALERT
output pin can operate in two different
modes overtemperature mode and SMBus alert mode. The
pin defaults to overtemperature mode on power up. This
means that it becomes active when the measured
temperature meets or exceeds the limit stored in the T
OS
setpoint register. At this point it can deal with the event in
one of two ways which depends on the mode it is in. The two
overtemperature modes are: comparator mode and interrupt
mode. Comparator mode is the default mode on power up.
More information on comparator and interrupt modes
alsong with the SMBus alert mode are explained below.
Comparator Mode
In Comparator Mode, the OS
/ALERT
pin becomes active
when the measured temperature equals or exceeds the limit
stored in the T
OS
setpoint register. The pin returns to its
inactive status when the temperature drops below the T
HYST
setpoint register value.
NOTE: Shutdown mode does not reset the output state for
comparator mode.
Interrupt Mode
In the interrupt mode, the OS
/ALERT
pin becomes active
when the temperature equals or exceeds the T
OS
limit for
a consecutive number of faults. It can be reset by performing
a read operation on any register in the NCT75. The output
can only become active again when the T
OS
limit has been
equalled or exceeded.
Figure 11 shows how both the interrupt and comparator
modes operate in relation to the output pin (OS
/ALERT
). It
also shows the operation of the polarity bit in the
configuration register.
相關PDF資料 |
PDF描述 |
|---|---|
| NCV8881PWR2G | IC REG TRPL BUCK/LINEAR 16SOIC |
| NE1617ADS,112 | IC TEMP MONITOR 16SSOP |
| NE1619DS,118 | IC TEMP MONITOR 16SSOP |
| NIS5112D1R2G | IC ELECTRONIC FUSE HOTSWAP 8SOIC |
| NIS5132MN2TXG | IC ELECTRONIC FUSE 12V 10DFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCT7717U TR | 制造商:Nuvoton Technology Corp 功能描述:SMBUS INTERFACE TEMP. SENSOR W 制造商:Nuvoton Technology Corp 功能描述:IC SMBUS TEMP SENSOR 8MSOP |
| NCT7718W TR | 制造商:Nuvoton Technology Corp 功能描述:IC SMBUS TEMP SENSOR 8MSOP |
| NCT7802Y | 制造商:Nuvoton Technology Corp 功能描述: |
| NCT7904D | 制造商:Nuvoton Technology Corp 功能描述:IC H/W MONITOR |
| NCT80DBR2G | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。