- 您現在的位置：買賣IC網 > Datasheet目錄46 > NVT210DMTR2G (ON Semiconductor)IC TEMP SENSOR DGTL 8-WDFN Datasheet資料下載
參數資料
| 型號： | NVT210DMTR2G |
| 廠商： | ON Semiconductor |
| 文件頁數： | 15/20頁 |
| 文件大小： | 325K |
| 描述： | IC TEMP SENSOR DGTL 8-WDFN |
| 標準包裝： | 3,000 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | 0°C ~ 127°C，-64°C ~ 191°C |
| 精確度： | ±2.5°C |
| 拓撲： | ADC，比較器，多路復用器，寄存器庫 |
| 輸出類型： | 2 線串行，I²C?/SMBUS? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 2.8 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-WFDFN |
| 供應商設備封裝： | 8-WDFN（2x2） |
| 包裝： | 帶卷 (TR) |
NVT210
http://onsemi.com
15
The NVT210 Interrupt System
The NVT210 has two interrupt outputs, ALERT
and
THERM
. Both have different functions and behavior.
ALERT
is maskable and responds to violations of software
programmed temperature limits or an open-circuit fault on
the external diode. THERM
is intended as a fail-safe
interrupt output that cannot be masked.
If the external or local temperature exceeds the
programmed high temperature limits, or equals or exceeds
the low temperature limits, the ALERT
output is asserted
low. An open-circuit fault on the external diode also causes
ALERT
to assert. ALERT
is reset when serviced by a master
reading its device address, provided the error condition has
gone away and the status register has been reset.
The THERM
output asserts low if the external or local
temperature exceeds the programmed THERM
limits.
THERM
temperature limits should normally be equal to or
greater than the high temperature limits. THERM
is reset
automatically when the temperature falls back within the
THERM
limit. A hysteresis value can be programmed; in
which case, THERM
resets when the temperature falls to the
limit value minus the hysteresis value. This applies to both
local and remote measurement channels. The power-on
hysteresis default value is 10癈, but this can be
reprogrammed to any value after powerup.
The hysteresis loop on the THERM
outputs is useful when
THERM
is used, for example, as an on/off controller for a
fan. The users system can be set up so that when THERM
asserts, a fan is switched on to cool the system. When
THERM
goes high again, the fan can be switched off.
Programming a hysteresis value protects from fan jitter,
where the temperature hovers around the THERM
limit, and
the fan is constantly switched.
Table 14. THERM
HYSTERESIS
THERM
Hysteresis
Binary Representation
0癈
0 000 0000
1癈
0 000 0001
10癈
0 000 1010
Figure 19 shows how the THERM
and ALERT
outputs
operate. The ALERT
output can be used as a SMBALERT
to signal to the host via the SMBus/I
2
C that the temperature
has risen. The user can use the THERM
output to turn on a
fan to cool the system, if the temperature continues to
increase. This method ensures that there is a fail-safe
mechanism to cool the system, without the need for host
intervention.
Figure 19. Operation of the ALERT
and THERM
Interrupts
1005C
THERM
LIMIT
905C
805C
705C
605C
505C
405C
THERM
LIMIT HYSTERESIS
HIGH TEMP LIMIT
RESET BY MASTER
TEMPERATURE
1
2
3
4
ALERT
THERM
?SPAN class="pst NVT210DMTR2G_2295433_3"> If the measured temperature exceeds the high
temperature limit, the ALERT
output asserts low.
?SPAN class="pst NVT210DMTR2G_2295433_3"> If the temperature continues to increase and exceeds the
THERM
limit, the THERM
output asserts low.
?SPAN class="pst NVT210DMTR2G_2295433_3"> The THERM
output deasserts (goes high) when the
temperature falls to THERM
limit minus hysteresis. In ,
the default hysteresis value of 10癈 is shown.
?SPAN class="pst NVT210DMTR2G_2295433_3"> The ALERT
output deasserts only when the
temperature has fallen below the high temperature
limit, and the master has read the device address and
cleared the status register.
?SPAN class="pst NVT210DMTR2G_2295433_3"> Pin 6 on the NVT210 can be configured as either an
ALERT
output or as an additional THERM
output.
?SPAN class="pst NVT210DMTR2G_2295433_3"> THERM2
asserts low when the temperature exceeds the
programmed local and/or remote high temperature
limits. It is reset in the same manner as THERM
and is
not maskable.
?SPAN class="pst NVT210DMTR2G_2295433_3"> The programmed hysteresis value also applies to
THERM2
.
Figure 20 shows how THERM
and THERM2
operate
together to implement two methods of cooling the system.
In this example, the THERM2
limits are set lower than the
THERM
limits. The THERM2
output is used to turn on a
fan.
相關PDF資料 |
PDF描述 |
|---|---|
| PI5L102LE | IC HOT SWAP PULL-UP SW 20-TSSOP |
| QPI-8LZ-01 | IC HOT SWAP EMI FILTER 16LGA |
| SA56004HD,118 | IC TEMP SENSOR DIGITAL 8SOIC |
| SC2463TSTRT | IC REG QD BCK/LINEAR 28TSSOP |
| SC338AIMSTRT | IC REG CTRLR DUAL POS ADJ 10MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NVT-3402 | 制造商:Quest Technology International Inc 功能描述: |
| NVT-3403 | 制造商:Quest Technology International Inc 功能描述: |
| NVT4555UKZ | 功能描述:SIM Card Interface 12-WLCSP (1.20x1.60) 制造商:nxp semiconductors 系列:- 包裝:剪切帶（CT） 零件狀態:停產 應用:SIM 卡 接口:- 電壓 - 電源:1.1 V ~ 3.6 V 封裝/外殼:12-UFBGA 供應商器件封裝:12-WLCSP（1.20x1.60） 安裝類型:表面貼裝 標準包裝:1 |
| NVT4556AUKZ | 功能描述:SIM Card Interface 12-WLCSP (1.20x1.60) 制造商:nxp semiconductors 系列:- 包裝:剪切帶（CT） 零件狀態:有效 應用:SIM 卡 接口:I2C 電壓 - 電源:1.55 V ~ 3.6 V 封裝/外殼:12-XFBGA 供應商器件封裝:12-WLCSP（1.20x1.60） 安裝類型:表面貼裝 標準包裝:1 |
| NVT4556BUKZ | 功能描述:SIM Card Interface 12-WLCSP (1.20x1.60) 制造商:nxp semiconductors 系列:- 包裝:剪切帶（CT） 零件狀態:有效 應用:SIM 卡 接口:I2C 電壓 - 電源:1.55 V ~ 3.6 V 封裝/外殼:12-XFBGA 供應商器件封裝:12-WLCSP（1.20x1.60） 安裝類型:表面貼裝 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。