- 您現在的位置：買賣IC網 > Datasheet目錄46 > NVT210DMTR2G (ON Semiconductor)IC TEMP SENSOR DGTL 8-WDFN Datasheet資料下載
參數資料
| 型號： | NVT210DMTR2G |
| 廠商： | ON Semiconductor |
| 文件頁數： | 7/20頁 |
| 文件大小： | 325K |
| 描述： | IC TEMP SENSOR DGTL 8-WDFN |
| 標準包裝： | 3,000 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | 0°C ~ 127°C，-64°C ~ 191°C |
| 精確度： | ±2.5°C |
| 拓撲： | ADC，比較器，多路復用器，寄存器庫 |
| 輸出類型： | 2 線串行，I²C?/SMBUS? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 2.8 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-WFDFN |
| 供應商設備封裝： | 8-WDFN（2x2） |
| 包裝： | 帶卷 (TR) |
NVT210
http://onsemi.com
7
Theory of Operation
The NVT210 is a local and remote temperature sensor and
over/under temperature alarm, with the added ability to
automatically cancel the effect of 1.5 kW (typical) of
resistance in series with the temperature monitoring diode.
When the NVT210 is operating normally, the on-board ADC
operates in a free running mode. The analog input
multiplexer alternately selects either the on-chip
temperature sensor to measure its local temperature or the
remote temperature sensor. The ADC digitizes these signals
and the results are stored in the local and remote temperature
value registers.
The local and remote measurement results are compared
with the corresponding high, low, and THERM
temperature
limits, stored in eight on-chip registers. Out-of-limit
comparisons generate flags that are stored in the status
register. A result that exceeds the high temperature limit or
the low temperature limit causes the ALERT
output to
assert. The ALERT
output also asserts if an external diode
fault is detected. Exceeding the THERM
temperature limits
causes the THERM
output to assert low. The ALERT
output
can be reprogrammed as a second THERM
output.
The limit registers are programmed and the device
controlled and configured via the serial SMBus/I
2
C. The
contents of any register are also read back via the
SMBus/I
2
C.
Control and configuration functions consist of switching
the device between normal operation and standby mode,
selecting the temperature measurement range, masking or
enabling the ALERT
output, switching Pin 6 between
ALERT
and THERM2
, and selecting the conversion rate.
Series Resistance Cancellation
Parasitic resistance to the D+ and D inputs to the
NVT210, seen in series with the remote diode, is caused by
a variety of factors, including PCB track resistance and track
length. This series resistance appears as a temperature offset
in the remote sensors temperature measurement. This error
typically causes a 0.5癈 offset per ohm of parasitic
resistance in series with the remote diode.
The NVT210 automatically cancels the effect of this
series resistance on the temperature reading, giving a more
accurate result, without the need for user characterization of
this resistance. The NVT210 is designed to automatically
cancel typically up to 1.5 kW of resistance. By using an
advanced temperature measurement method, this process is
transparent to the user. This feature permits resistances to be
added to the sensor path to produce a filter, allowing the part
to be used in noisy environments. See the section on Noise
Filtering for more details.
Temperature Measurement Method
A simple method of measuring temperature is to exploit
the negative temperature coefficient of a diode, measuring
the base emitter voltage (V
BE
) of a transistor operated at
constant current. However, this technique requires
calibration to null the effect of the absolute value of V
BE
,
which varies from device to device.
The technique used in the NVT210 measures the change
in V
BE
when the device operates at three different currents.
Previous devices used only two operating currents, but it is
the use of a third current that allows automatic cancellation
of resistances in series with the external temperature sensor.
Figure 14 shows the input signal conditioning used to
measure the output of an external temperature sensor. This
figure shows the external sensor as a substrate transistor, but
it can equally be a discrete transistor. If a discrete transistor
is used, the collector is not grounded but is linked to the base.
To prevent ground noise interfering with the measurement,
the more negative terminal of the sensor is not referenced to
ground, but is biased above ground by an internal diode at
the D input. C1 may be added as a noise filter
(a recommended maximum value of 1,000 pF). However, a
better option in noisy environments is to add a filter, as
described in the Noise Filtering section. See the Layout
Considerations section for more information on C1.
To measure DV
BE
, the operating current through the
sensor is switched among three related currents. As shown
in Figure 14, N1 ?I and N2 ?I are different multiples of the
current, I. The currents through the temperature diode are
switched between I and N1 ?I, giving DV
BE1
; and then
between I and N2 ?I, giving DV
BE2
. The temperature is
then calculated using the two DV
BE
measurements. This
method also cancels the effect of any series resistance on the
temperature measurement.
The resulting DV
BE
waveforms are passed through a
65 kHz low-pass filter to remove noise and then to a
chopper-stabilized amplifier. This amplifies and rectifies the
waveform to produce a dc voltage proportional to DV
BE
.
The ADC digitizes this voltage producing a temperature
measurement. To reduce the effects of noise, digital filtering
is performed by averaging the results of 16 measurement
cycles for low conversion rates. At rates of 16-, 32-, and
64-conversions/second, no digital averaging occurs.
Signal conditioning and measurement of the internal
temperature sensor are performed in the same manner.
相關PDF資料 |
PDF描述 |
|---|---|
| PI5L102LE | IC HOT SWAP PULL-UP SW 20-TSSOP |
| QPI-8LZ-01 | IC HOT SWAP EMI FILTER 16LGA |
| SA56004HD,118 | IC TEMP SENSOR DIGITAL 8SOIC |
| SC2463TSTRT | IC REG QD BCK/LINEAR 28TSSOP |
| SC338AIMSTRT | IC REG CTRLR DUAL POS ADJ 10MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NVT-3402 | 制造商:Quest Technology International Inc 功能描述: |
| NVT-3403 | 制造商:Quest Technology International Inc 功能描述: |
| NVT4555UKZ | 功能描述:SIM Card Interface 12-WLCSP (1.20x1.60) 制造商:nxp semiconductors 系列:- 包裝:剪切帶（CT） 零件狀態:停產 應用:SIM 卡 接口:- 電壓 - 電源:1.1 V ~ 3.6 V 封裝/外殼:12-UFBGA 供應商器件封裝:12-WLCSP（1.20x1.60） 安裝類型:表面貼裝 標準包裝:1 |
| NVT4556AUKZ | 功能描述:SIM Card Interface 12-WLCSP (1.20x1.60) 制造商:nxp semiconductors 系列:- 包裝:剪切帶（CT） 零件狀態:有效 應用:SIM 卡 接口:I2C 電壓 - 電源:1.55 V ~ 3.6 V 封裝/外殼:12-XFBGA 供應商器件封裝:12-WLCSP（1.20x1.60） 安裝類型:表面貼裝 標準包裝:1 |
| NVT4556BUKZ | 功能描述:SIM Card Interface 12-WLCSP (1.20x1.60) 制造商:nxp semiconductors 系列:- 包裝:剪切帶（CT） 零件狀態:有效 應用:SIM 卡 接口:I2C 電壓 - 電源:1.55 V ~ 3.6 V 封裝/外殼:12-XFBGA 供應商器件封裝:12-WLCSP（1.20x1.60） 安裝類型:表面貼裝 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。