- 您現在的位置：買賣IC網 > PDF目錄382379 > PCA9545PW (NXP SEMICONDUCTORS) 4-channel I2C switch with interrupt logic and reset PDF資料下載
參數資料
| 型號： | PCA9545PW |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 通用總線功能 |
| 英文描述： | 4-channel I2C switch with interrupt logic and reset |
| 中文描述： | 9545 SERIES, 4 LINE TO 1 LINE MULTIPLEXER, TRUE OUTPUT, PDSO20 |
| 封裝： | 4.40 MM, PLASTIC, MO-153, SOT-360-1, TSSOP-20 |
| 文件頁數： | 4/14頁 |
| 文件大?。?/td> | 118K |
| 代理商： | PCA9545PW |
Philips Semiconductors
Product data
PCA9545
4-channel I
2
C switch with interrupt logic and reset
2002 Mar 28
4
853-2302 27311
DEVICE ADDRESS
Following a START condition the bus master must output the
address of the slave it is accessing. The address of the PCA9545 is
shown in Figure 3. To conserve power, no internal pullup resistors
are incorporated on the hardware selectable address pins and they
must be pulled HIGH or LOW.
A1 A0
1
1
0
0
SW00893
1
R/W
FIXED
HARDWARE SELECTABLE
Figure 3. Slave address
The last bit of the slave address defines the operation to be
performed. When set to logic 1, a read is selected while a logic 0
selects a write operation.
CONTROL REGISTER
Following the successful acknowledgement of the slave address,
the bus master will send a byte to the PCA9545, which will be stored
in the control register. If multiple bytes are received by the
PCA9545, it will save the last byte received. This register can be
written and read via the I
2
C bus.
SW00949
CHANNEL SELECTION BITS
(READ/WRITE)
INTERRUPT BITS
(READ ONLY)
6
5
4
2
1
0
7
3
CHANNEL 0
CHANNEL 1
CHANNEL 2
CHANNEL 3
INT0
INT1
INT2
INT3
INT3 INT2 INT1 INT0
B3
B2
B1
B0
Figure 4. Control Register
CONTROL REGISTER DEFINITION
One or several SCx/SDx downstream pair, or channel, is selected
by the contents of the control register. This register is written after
the PCA9545 has been addressed. The 2 LSBs of the control byte
are used to determine which channel is to be selected. When a
channel is selected, the channel will become active after a stop
condition has been placed on the I
2
C bus. This ensures that all
SCx/SDx lines will be in a HIGH state when the channel is made
active, so that no false conditions are generated at the time of
connection.
Table 1. Control Register; Write — Channel Selection/
Read — Channel Status
INT3
INT2
INT1
INT0
B3
B2
B1
B0
COMMAND
Channel 0
disabled
Channel 0
enabled
Channel 1
disabled
Channel 1
enabled
Channel 2
disabled
Channel 2
enabled
Channel 3
disabled
Channel 3
enabled
X
X
X
X
X
X
X
0
1
X
X
X
X
X
X
0
X
1
X
X
X
X
X
0
X
X
1
X
X
X
X
0
X
X
X
1
NOTE:
Several channels can be enabled at the same time.
Ex: B3 = 0, B2 = 1, B1 = 1, B0 = 0, means that channel 0 and 3 are
disabled and channel 1 and 2 are enabled.
Care should be taken not to exceed the maximum bus capacity.
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9548A | 8-channel I2C switch with reset |
| PCA9548 | 8-channel I2C switch with reset |
| PCA9548D | 8-channel I2C switch with reset |
| PCA9548PW | 8-channel I2C switch with reset |
| PCA9550 | 2-bit I2C LED driver with programmable blink rates |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9546 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:4-channel I2C switch with reset |
| PCA9546A | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4-CHANNEL I2C AND SMBus SWITCH WITH RESET FUNCTION |
| PCA9546A_1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4-CHANNEL I2C AND SMBus SWITCH WITH RESET FUNCTION |
| PCA9546A_2 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4-CHANNEL I2C AND SMBus SWITCH WITH RESET FUNCTION |
| PCA9546A_3 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4-CHANNEL I2C AND SMBus SWITCH WITH RESET FUNCTION |
發布緊急采購，3分鐘左右您將得到回復。