欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: PSD854F2V-90
廠商: 意法半導體
英文描述: Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
中文描述: Flash在系統可編程(ISP)的周邊8位MCU,5V的
文件頁數: 67/110頁
文件大小: 1737K
代理商: PSD854F2V-90
67/110
PSD813F2, PSD833F2, PSD834F2, PSD853F2, PSD854F2
RESET TIMING AND DEVICE STATUS AT RESET
Power-Up Reset
Upon Power-up, the PSD requires a Reset (RE-
SET) pulse of duration t
NLNH-PO
after V
CC
is
steady. During this period, the device loads inter-
nal configurations, clears some of the registers
and sets the Flash memory into Operating mode.
After the rising edge of Reset (RESET), the PSD
remains in the Reset mode for an additional peri-
od, t
OPR
, before the first memory access is al-
lowed.
The Flash memory is reset to the READ Mode
upon Power-up. Sector Select (FS0-FS7 and
CSBOOT0-CSBOOT3) must all be Low, Write
Strobe (WR, CNTL0) High, during Power On Re-
set for maximum security of the data contents and
to remove the possibility of a byte being written on
the first edge of Write Strobe (WR, CNTL0). Any
Flash memory WRITE cycle initiation is prevented
automatically when V
CC
is below V
LKO
.
Warm Reset
Once the device is up and running, the device can
be reset with a pulse of a much shorter duration,
t
NLNH
.
The same t
OPR
period is needed before the device
is operational after warm reset. Figure
34
shows
the timing of the Power-up and warm reset.
I/O Pin, Register and PLD Status at Reset
Table 33., page 68
shows the I/O pin, register and
PLD status during Power On Reset, warm reset
and Power-down mode. PLD outputs are always
valid during warm reset, and they are valid in Pow-
er On Reset once the internal PSD Configuration
bits are loaded. This loading of PSD is completed
typically long before the V
CC
ramps up to operat-
ing level. Once the PLD is active, the state of the
outputs are determined by the PSDabel equa-
tions.
Reset of Flash Memory Erase and Program
Cycles (on the PSD834Fx)
A Reset (RESET) also resets the internal Flash
memory state machine. During a Flash memory
Program or Erase cycle, Reset (RESET) termi-
nates the cycle and returns the Flash memory to
the Read Mode within a period of t
NLNH-A
.
Figure 34. Reset (RESET) Timing
tNLNH-PO
Power-On Reset
tOPR
AI02866b
RESET
tNLNH
tNLNH-A
Warm Reset
tOPR
V
CC
V
CC
(min)
相關PDF資料
PDF描述
PSD854F3V-15 Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD854F3V-20 Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD854F3V-70 Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD913212JIT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913212JT Terminal Block; Pitch Spacing:0.197"; Wire Size (AWG):26-12; Mounting Type:PC Board; Leaded Process Compatible:No; Peak Reflow Compatible (260 C):No; Terminal Block Clamp Type:Tension Clamp
相關代理商/技術參數
參數描述
PSD854F2V-90J 功能描述:CPLD - 復雜可編程邏輯器件 3.0V 2M 90ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
PSD854F2V-90M 功能描述:CPLD - 復雜可編程邏輯器件 3.0V 2M 90ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
PSD-8M-01 制造商:Richco 功能描述:CB SPT REST MNT NAT 8MM SPC
PSD913212JIT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913212JT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
主站蜘蛛池模板: 济源市| 集贤县| 石家庄市| 仲巴县| 高要市| 康马县| 光山县| 元阳县| 昌乐县| 抚远县| 津市市| 尼木县| 通州市| 池州市| 邵武市| 景东| 南陵县| 永安市| 黔西县| 响水县| 长子县| 逊克县| 乾安县| 云梦县| 库尔勒市| 彰化县| 榆林市| 贵港市| 西乌珠穆沁旗| 留坝县| 乐至县| 尼玛县| 汝城县| 富裕县| 稷山县| 龙山县| 克山县| 浦北县| 南华县| 托克托县| 炉霍县|