- 您現在的位置：買賣IC網 > PDF目錄361226 > Q6701-H6481 (SIEMENS AG) Quadruple Transceiver for S/T Interface QUAT-S PDF資料下載
參數資料
| 型號： | Q6701-H6481 |
| 廠商： | SIEMENS AG |
| 英文描述： | Quadruple Transceiver for S/T Interface QUAT-S |
| 中文描述： | 四聯收發器的S / T接口葛- ? |
| 文件頁數： | 32/72頁 |
| 文件大小： | 1267K |
| 代理商： | Q6701-H6481 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
PEB 2084
Semiconductor Group
32
3
All procedures required for data transmission over the S/T interface are implemented.
These comprise the S/T interface frame and multiframe synchronization,
activation/deactivation procedure, and timing requirements such as bit rate and jitter. For
a correct functionality of the QUAT-S the following operational precautions must be
taken:
Operational Description
3.1
At power up, a reset pulse (RST) should be applied to bring the line interfaces of the
PEB 2084, QUAT-S, to the state “reset”. No clocks are required during that procedure.
After that the PEB 2084, QUAT-S, may be operated according to the state diagram,
each line interface controlled via the corresponding C/I channel.
Reset
3.2
The QUAT-S senses whether an external pull-up resistor (100 k
to 1 M
) is connected
to the pin IDO. The sensing is done after reset within the following two IOM frames in the
monitor channel.
The pin is pulled low for one bit and then switched to tristate. If the voltage level at IDP0
rises in the next bit to “High”, QUAT-S interprets this behaviour as an external pull up
being connected to the pin and remains as open collector. If the level stays at “Low”
QUAT-S switches to push-pull. However, actions of other device on this line or crosstalk
from other lines during the sensing procedure may falsify the result. (A pull down resistor
of 100 k
to 1 M
may improve the correctness of the sensing). This feature is useful if
multiple transmitters are connected to the same IOM-2 interface, e.g. QUAT-S with an
IDEC.
Push – Pull Sensing on Pin IDO
3.3
IOM
-2 Interface
3.3.1
The allocation between S/T line interfaces and the IOM-2 ISDN channels is according to
their numbers with an offset of four or zero. The offset can be selected via pin ICS by pin
strapping, i.e.
for ICS = 0 the SRX0a,b is allocated to IOM channel 0, and so on,
for ICS = 1 the SRX0a,b is allocated to IOM channel 4, and so on.
For detailed electrical definition refer to the
chapter 5
and the IOM Interface
Specification, Rev. 2.
As described in
chapter 2.2.2
, each basic ISDN channel consists of five different
communication channels: two voice channels, one monitor channel (incl. MR and MX
bits), one D-channel and one command/indication (C/I) channel.
ISDN Channels Allocation
相關PDF資料 |
PDF描述 |
|---|---|
| Q67020-Y149 | Octal Latch |
| Q67020-Y150 | Octal Latch |
| Q67020-Y151 | CLOCK GENERATOR AND DRIVER FOR SAB8086 FAMILY PROCESSORS |
| Q67020-Y152 | CLOCK GENERATOR AND DRIVER FOR SAB8086 FAMILY PROCESSORS |
| Q67020-Y153 | OCTAL BUS TRANSCEIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| Q67020-Y149 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:Octal Latch |
| Q67020-Y150 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:Octal Latch |
| Q67020-Y151 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:CLOCK GENERATOR AND DRIVER FOR SAB8086 FAMILY PROCESSORS |
| Q67020-Y152 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:CLOCK GENERATOR AND DRIVER FOR SAB8086 FAMILY PROCESSORS |
| Q67020-Y153 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:OCTAL BUS TRANSCEIVER |
發布緊急采購，3分鐘左右您將得到回復。