欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號： S29GL032M10FAIR33
廠商： SPANSION LLC
元件分類： PROM
英文描述： MirrorBit Flash Family
中文描述： 2M X 16 FLASH 3V PROM, 100 ns, PBGA64
封裝： 13 X 11 MM, FORTIFIED, BGA-64
文件頁數： 76/116頁
文件大小： 6024K
代理商： S29GL032M10FAIR33
60
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B8 February 7, 2007
Data
Sheet
Command Definitions
Writing specific address and data commands or sequences into the command register initiates
device operations. Table 34 and Table 35 define the valid register command sequences. Writing
incorrect address and data values or writing them in the improper sequence may place the device
in an unknown state. A reset command is then required to return the device to reading array data.
All addresses are latched on the falling edge of WE# or CE#, whichever happens later. All data is
latched on the rising edge of WE# or CE#, whichever happens first. See AC Characteristics for
timing diagrams.
Reading Array Data
The device is automatically set to reading array data after device power-up. No commands are
required to retrieve data. The device is ready to read array data after completing an Embedded
Program or Embedded Erase algorithm.
After the device accepts an Erase Suspend command, the device enters the erase-suspend-read
mode, after which the system can read data from any non-erase-suspended sector. After com-
pleting a programming operation in the Erase Suspend mode, the system may once again read
array data with the same exception. See Erase Suspend/Erase Resume Commands for more
information.
The system must issue the reset command to return the device to the read (or erase-suspend-
read) mode if DQ5 goes high during an active program or erase operation, or if the device is in
the autoselect mode. See the next section, Reset Command, for more information.
See also Requirements for Reading Array Data in the Device Bus Operations section for more in-
formation. The Read-Only Operations–AC Characteristics provides the read parameters, and
Figure 13 shows the timing diagram.
Reset Command
Writing the reset command resets the device to the read or erase-suspend-read mode. Address
bits are don’t cares for this command.
The reset command may be written between the sequence cycles in an erase command sequence
before erasing begins. This resets the device to the read mode. Once erasure begins, however,
the device ignores reset commands until the operation is complete.
The reset command may be written between the sequence cycles in a program command se-
quence before programming begins. This resets the device to the read mode. If the program
command sequence is written while the device is in the Erase Suspend mode, writing the reset
command returns the device to the erase-suspend-read mode. Once programming begins, how-
ever, the device ignores reset commands until the operation is complete.
The reset command may be written between the sequence cycles in an autoselect command se-
quence. Once in the autoselect mode, the reset command must be written to return to the read
mode. If the device entered the autoselect mode while in the Erase Suspend mode, writing the
reset command returns the device to the erase-suspend-read mode.
If DQ5 goes high during a program or erase operation, writing the reset command returns the
device to the read mode (or erase-suspend-read mode if the device was in Erase Suspend).
Note that if DQ1 goes high during a Write Buffer Programming operation, the system must write
the Write-to-Buffer-Abort Reset command sequence to reset the device for the next operation.
相關PDF資料
PDF描述
S29GL032M10FAIR40 MirrorBit Flash Family
S29GL032M10FAIR42 MirrorBit Flash Family
S29GL032M10FAIR43 CAPACITOR TANT 330UF 4V 20% SMD
S29GL032M10FFIR12 MirrorBit Flash Family
S29GL032M10FFIR20 MirrorBit Flash Family
相關代理商/技術參數
參數描述
S29GL032M10FAIR40 制造商:SPANSION 制造商全稱:SPANSION 功能描述:3.0 Volt-only Page Mode Flash Memory featuring 0.23 um MirrorBit process technology
S29GL032M10FAIR42 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family
S29GL032M10FAIR43 制造商:SPANSION 制造商全稱:SPANSION 功能描述:256,128,64,32,Megabit 3.0 Volt-only Page Mode Flash Memory featuring 0.23 レm MirrorBit Process Technology
S29GL032M10FAIR50 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family
S29GL032M10FAIR52 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*
主站蜘蛛池模板： 石首市| 阳朔县| 章丘市| 钟山县| 博爱县| 司法| 根河市| 阿拉善右旗| 凉城县| 阿城市| 井陉县| 西藏| 安康市| 云浮市| 东乌珠穆沁旗| 葵青区| 汉中市| 长岛县| 新晃| 文昌市| 灵寿县| 民县| 大英县| 朝阳市| 虹口区| 大邑县| 彝良县| 邢台县| 黄浦区| 湘潭县| 怀化市| 剑河县| 沿河| 西宁市| 伊通| 南充市| 荆门市| 丽水市| 绥中县| 兴文县| 上饶市|