- 您現在的位置：買賣IC網 > PDF目錄192296 > S29GL032M10FAIR33 (SPANSION LLC) MirrorBit Flash Family PDF資料下載
參數資料
| 型號： | S29GL032M10FAIR33 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | MirrorBit Flash Family |
| 中文描述： | 2M X 16 FLASH 3V PROM, 100 ns, PBGA64 |
| 封裝： | 13 X 11 MM, FORTIFIED, BGA-64 |
| 文件頁數： | 92/116頁 |
| 文件大小： | 6024K |
| 代理商： | S29GL032M10FAIR33 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁當前第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
February 7, 2007 S29GL-M_00_B8
S29GL-M MirrorBitTM Flash Family
75
Data
Sheet
Figure 8 shows the toggle bit algorithm in flowchart form, and the section “DQ2: Toggle Bit II”
explains the algorithm, also see RY/BY#: Ready/Busy#. Figure 20 shows the toggle bit timing di-
agram. Figure 21 shows the differences between DQ2 and DQ6 in graphical form.
Whenever the system initially begins reading toggle bit status, it must read DQ7–DQ0 at least
twice in a row to determine whether a toggle bit is toggling. Typically, the system would note and
store the value of the toggle bit after the first read. After the second read, the system would com-
pare the new value of the toggle bit with the first. If the toggle bit is not toggling, the device has
completed the program or erase operation. The system can read array data on DQ7–DQ0 on the
following read cycle.
However, if after the initial two read cycles, the system determines that the toggle bit is still tog-
gling, the system also should note whether the value of DQ5 is high (see the section on DQ5). If
it is, the system should then determine again whether the toggle bit is toggling, since the toggle
bit may have stopped toggling just as DQ5 went high. If the toggle bit is no longer toggling, the
device has successfully completed the program or erase operation. If it is still toggling, the device
did not completed the operation successfully, and the system must write the reset command to
return to reading array data.
The remaining scenario is that the system initially determines that the toggle bit is toggling and
DQ5 did not go high. The system may continue to monitor the toggle bit and DQ5 through suc-
cessive read cycles, determining the status as described in the previous paragraph. Alternatively,
it may choose to perform other system tasks. In this case, the system must start at the beginning
of the algorithm when it returns to determine the status of the operation (top of Figure 6).
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program, erase, or write-to-buffer time exceeded a specified internal
pulse count limit. Under these conditions DQ5 produces a “1,” indicating that the program or erase
cycle was not successfully completed.
The device may output a “1” on DQ5 if the system tries to program a “1” to a location that was
previously programmed to “0.” Only an erase operation can change a “0” back to a “1.”
Under this condition, the device halts the operation, and when the timing limit is exceeded, DQ5
produces a “1.”
In all these cases, the system must write the reset command to return the device to the reading
the array (or to erase-suspend-read if the device was previously in the erase-suspend-program
mode).
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the system may read DQ3 to determine whether
or not erasure started. (The sector erase timer does not apply to the chip erase command.) If
additional sectors are selected for erasure, the entire time-out also applies after each additional
sector erase command. When the time-out period is complete, DQ3 switches from a “0” to a “1.”
If the time between additional sector erase commands from the system can be assumed to be
less than 50 s, the system need not monitor DQ3(see Sector Erase Command Sequence).
After the sector erase command is written, the system should read the status of DQ7 (Data# Poll-
ing) or DQ6 (Toggle Bit I) to ensure that the device accepted the command sequence, and then
reads DQ3. If DQ3 is “1,” the Embedded Erase algorithm started; all further commands (except
Erase Suspend) are ignored until the erase operation is complete. If DQ3 is “0,” the device accepts
additional sector erase commands. To ensure the command was accepted, the system software
should check the status of DQ3 prior to and following each subsequent sector erase command. If
DQ3 is high on the second status check, the last command might not have been accepted.
Table 36 shows the status of DQ3 relative to the other status bits.
DQ1: Write-to-Buffer Abort
DQ1 indicates whether a Write-to-Buffer operation was aborted. Under these conditions DQ1 pro-
duces a “1”. The system must issue the Write-to-Buffer-Abort-Reset command sequence to return
the device to reading array data. See Write Buffer for more details.
相關PDF資料 |
PDF描述 |
|---|---|
| S29GL032M10FAIR40 | MirrorBit Flash Family |
| S29GL032M10FAIR42 | MirrorBit Flash Family |
| S29GL032M10FAIR43 | CAPACITOR TANT 330UF 4V 20% SMD |
| S29GL032M10FFIR12 | MirrorBit Flash Family |
| S29GL032M10FFIR20 | MirrorBit Flash Family |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29GL032M10FAIR40 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:3.0 Volt-only Page Mode Flash Memory featuring 0.23 um MirrorBit process technology |
| S29GL032M10FAIR42 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family |
| S29GL032M10FAIR43 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:256,128,64,32,Megabit 3.0 Volt-only Page Mode Flash Memory featuring 0.23 レm MirrorBit Process Technology |
| S29GL032M10FAIR50 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family |
| S29GL032M10FAIR52 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family |
發布緊急采購，3分鐘左右您將得到回復。