- 您現在的位置：買賣IC網 > PDF目錄192296 > S29GL032M10FAIR43 (SPANSION LLC) CAPACITOR TANT 330UF 4V 20% SMD PDF資料下載
參數資料
| 型號： | S29GL032M10FAIR43 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | CAPACITOR TANT 330UF 4V 20% SMD |
| 中文描述： | 2M X 16 FLASH 3V PROM, 100 ns, PBGA64 |
| 封裝： | 13 X 11 MM, FORTIFIED, BGA-64 |
| 文件頁數： | 77/116頁 |
| 文件大小： | 6024K |
| 代理商： | S29GL032M10FAIR43 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁當前第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
February 7, 2007 S29GL-M_00_B8
S29GL-M MirrorBitTM Flash Family
61
Data
Sheet
Autoselect Command Sequence
The autoselect command sequence allows the host system to read several identifier codes at spe-
cific addresses:
Note: 3.The device ID is read over three cycles. SA = Sector Address
The autoselect command sequence is initiated by first writing two unlock cycles. This is followed
by a third write cycle that contains the autoselect command. The device then enters the autose-
lect mode. The system may read at any address any number of times without initiating another
autoselect command sequence:
The system must write the reset command to return to the read mode (or erase-suspend-read
mode if the device was previously in Erase Suspend).
Enter/Exit Secured Silicon Sector Command Sequence
The Secured Silicon Sector region provides a secured data area containing an 8-word/16-byte
random Electronic Serial Number (ESN). The system can access the Secured Silicon Sector region
by issuing the three-cycle Enter Secured Silicon Sector command sequence. The device continues
to access the Secured Silicon Sector region until the system issues the four-cycle Exit Secured
Silicon Sector command sequence. The Exit Secured Silicon Sector command sequence returns
for both command sequences. Also, see Secured Silicon Sector Flash Memory Region for further
information. Note that the ACC function and unlock bypass modes are not available when the Se-
cured Silicon Sector is enabled.
Word Program Command Sequence
Programming is a four-bus-cycle operation. The program command sequence is initiated by writ-
ing two unlock write cycles, followed by the program set-up command. The program address and
data are written next, which in turn initiate the Embedded Program algorithm. The system is not
required to provide further controls or timings. The device automatically provides internally gen-
address and data requirements for the word program command sequence, respectively.
When the Embedded Program algorithm is complete, the device then returns to the read mode
and addresses are no longer latched. The system can determine the status of the program oper-
ation by using DQ7 or DQ6. See Write Operation Status for information on these status bits. Any
commands written to the device during the Embedded Program Algorithm are ignored. Note that
the Secured Silicon Sector, autoselect, and CFI functions are unavailable when a program oper-
ation is in progress. Note that a hardware reset immediately terminates the program operation.
The program command sequence should be reinitiated once the device returns to the read mode,
to ensure data integrity.
Programming is allowed in any sequence of address locations and across sector boundaries. Pro-
gramming to the same word address multiple times without intervening erases (incremental bit
programming) requires a modified programming method. For such application requirements,
please contact your local Spansion representative. Word programming is supported for backward
compatibility with existing Flash driver software and for occasional writing of individual words. Use
of write buffer programming (see below) is strongly recommended for general programming use
when more than a few words are to be programmed. The effective word programming time using
write buffer programming is approximately four times shorter than the single word programming
time.
Identifier Code
A7:A0
(x16)
A6:A-1
(x8)
Manufacturer ID
00h
Device ID, Cycle 1
01h
02h
Device ID, Cycle 2
0Eh
1Ch
Device ID, Cycle 3
0Fh
1Eh
Secured Silicon Sector Factory Protect
03h
06h
Sector Protect Verify
(SA)02h
(SA)04h
相關PDF資料 |
PDF描述 |
|---|---|
| S29GL032M10FFIR12 | MirrorBit Flash Family |
| S29GL032M10FFIR20 | MirrorBit Flash Family |
| S29GL032M10FFIR22 | Conductive Polymer Chip Capacitors / T530 Series - High Capacitance/Ultra-Low ESR; Capacitance [nom]: 1500uF; Working Voltage (Vdc)[max]: 2.5V; Capacitance Tolerance: +/-20%; Dielectric: Conductive Polymer; ESR: 5.0mΩ; Lead Style: Surface-Mount Chip; Lead Dimensions: 7343-43; Termination: 100% Tin (Sn); Body Dimensions: 7.3mm x 4.3mm x 4mm; Temperature Range: -55C to +125C; Container: Tape & Reel; Qty per Container: 500; Features: High Capacitance; Ultra-Low ESR |
| S29GL032M10FFIR23 | MirrorBit Flash Family |
| S29GL032M10FFIR30 | MirrorBit Flash Family |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29GL032M10FAIR50 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family |
| S29GL032M10FAIR52 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family |
| S29GL032M10FAIR53 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family |
| S29GL032M10FAIR60 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family |
| S29GL032M10FAIR62 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family |
發布緊急采購，3分鐘左右您將得到回復。