- 您現在的位置：買賣IC網 > PDF目錄98239 > TLC4545IDRG4 (TEXAS INSTRUMENTS INC) 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8 PDF資料下載
參數資料
| 型號： | TLC4545IDRG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | ADC |
| 英文描述： | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8 |
| 封裝： | GREEN, PLASTIC, MS-012AA, SOIC-8 |
| 文件頁數： | 5/26頁 |
| 文件大小： | 652K |
| 代理商： | TLC4545IDRG4 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
TLC4541, TLC4545
SLAS293 DECEMBER 2001
13
www.ti.com
PRINCIPLES OF OPERATION
control and timing (continued)
sampling and conversion cycle
TLC4541:
Control via pin 1, CS (FS = 1 at the falling edge of CS) The falling edge of CS is the start of the cycle.
Transitions on CS can occur when SCLK is high or low. The MSB may be read on the first falling SCLK edge
after CS is low. Output data changes on the rising edge of SCLK. This control method is typically used for a
microcontroller with an SPI interface, although it can also be used for a DSP. The microcontroller SPI
interface should be programmed for CPOL=0 (serial clock inactive low) and CPHA=1 (data valid on the
falling edge of serial clock).
Control via pin 7, FS (CS is tied/held low) The rising edge of FS is the start of the cycle. Transitions on FS
can occur when SCLK is high or low. The MSB is presented on SDO after the rising edge of FS. The MSB
may be read on the first falling edge of SCLK after the FS falling edge. Output data changes on the rising
edge of SCLK. This is the typical configuration when the ADC is the only device on the TMS320 DSP serial
port.
Control via pin 1 and pin 7, CS and FS Transitions on CS and FS can occur when SCLK is high or low. The
MSB is presented after the rising edge of FS. The falling edge of FS is the start of the sampling cycle. The
MSB may be read on the first falling edge of SCLK after the FS falling edge. Output data changes on the
rising edge of SCLK. This is typically used for multiple devices connected to a single TMS320 DSP serial
port.
TLC4545:
All control is provided using the CS input (pin 1) on the TLC4545. Transitions on CS can occur when SCLK is
high or low. The cycle is started on the falling edge transition on the CS input. This signal can be provided by
either a CS signal (when interfacing with an SPI microcontroller) or FS signal (when interfacing with a
TMS320 DSP). The MSB is presented to SDO on the falling edge of the signal applied to pin 1 and may be
read on the first falling SCLK edge after this input is low. Output data changes on the rising edge of SCLK.
control modes
control via pin 1 (CS, SPI interface)
All devices are compatible with this mode of operation. A falling edge on the CS input initiates the cycle. (For
the TLC4541, the FS input is tied to VDD ). The CS input remains low for the entire sampling time plus 4 SCLK
decoding time(16 falling SCLK edges) and can then be released at any point during the remainder of the
conversion. Enough time should be allowed before the next falling CS edge so that the conversion cycle is not
terminated prematurely. The microcontroller SPI interface should be programmed for CPOL=0 (serial clock
inactive low) and CPHA=1 (data is valid on the falling edge of serial clock).
ts
1
2
3
5
4
6
7
13
14
15
16
1
12
tconv
t(PWRDWN)
SDO Data is the Result of the Previous Sample
For TLC45xx, the LSB is Presented on the Rising SCLK 16th Edge
MSB
MSB1
MSB2 MSB3 MSB4 MSB5 MSB6
LSB4
LSB3
LSB2 LSB1
LSB
SCLK
CS
SDO
MSB
MSB1
24
Figure 15. SPI Cycle TIming Using the CS Input (FS = 1 for TLC4541)
相關PDF資料 |
PDF描述 |
|---|---|
| TLC4541IDR | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8 |
| TLC4545IDGK | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8 |
| TLC4545IDGKRG4 | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8 |
| TLC4541IDRG4 | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8 |
| TLC540INSG4 | 11-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLC-4C-0375 | 制造商:KATO/COILTHREAD 功能描述: |
| TLC-4C-0375W | 制造商:KATO/COILTHREAD 功能描述: |
| TLC-4C-0500 | 制造商:KATO/COILTHREAD 功能描述: |
| TL-C5-140-30 | 制造商:Newport Electronics Inc 功能描述:5-DOT ROUND LABELS |
| TLC530FTU | 功能描述:基準電壓& 基準電流 NPN 330V 7A RoHS:否 制造商:STMicroelectronics 產品:Voltage References 拓?fù)浣Y(jié)構:Shunt References 參考類型:Programmable 輸出電壓:1.24 V to 18 V 初始準確度:0.25 % 平均溫度系數（典型值）:100 PPM / C 串聯 VREF - 輸入電壓（最大值）: 串聯 VREF - 輸入電壓（最小值）: 分流電流（最大值）:60 mA 最大工作溫度:+ 125 C 封裝 / 箱體:SOT-23-3L 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。