欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: TLV320AIC33IRGZTG4
廠商: TEXAS INSTRUMENTS INC
元件分類: 消費家電
英文描述: SPECIALTY CONSUMER CIRCUIT, PQCC48
封裝: 7 X 7 MM, GREEN, PLASTIC, VQFN-48
文件頁數: 37/93頁
文件大小: 1427K
代理商: TLV320AIC33IRGZTG4
SHORT CIRCUIT OUTPUT PROTECTION
JACK / HEADSET DETECTION
SLAS480B – JANUARY 2006 – REVISED DECEMBER 2008 ........................................................................................................................................... www.ti.com
The high power output drivers include additional circuitry to avoid artifacts on the audio output during power-on
and power-off transient conditions. The user should first program the type of output configuration being used in
Page-0/Reg-14, to allow the device to select the optimal power-up scheme to avoid output artifacts. The
power-up delay time for the high power output drivers is also programmable over a wide range of time delays,
from instantaneous up to 4-sec, using Page-0/Reg-42.
When these output drivers are powered down, they can be placed into a variety of output conditions based on
register programming. If lowest power operation is desired, then the outputs can be placed into a tri-state
condition, and all power to the output stage is removed. However, this generally results in the output nodes
drifting to rest near the upper or lower analog supply, due to small leakage currents at the pins. This then results
in a longer delay requirement to avoid output artifacts during driver power-on. In order to reduce this required
power-on delay, the TLV320AIC33 includes an option for the output pins of the drivers to be weakly driven to the
VCM level they would normally rest at when powered with no signal applied. This output VCM level is determined
by an internal bandgap voltage reference, and thus results in extra power dissipation when the drivers are in
powerdown. However, this option provides the fastest method for transitioning the drivers from powerdown to full
power operation without any output artifact introduced.
The device includes a further option that falls between the other two – while it requires less power drawn while
the output drivers are in powerdown, it also takes a slightly longer delay to power-up without artifact than if the
bandgap reference is kept alive. In this alternate mode, the powered-down output driver pin is weakly driven to a
voltage of approximately half the DRVDD1/2 supply level using an internal voltage divider. This voltage will not
match the actual VCM of a fully powered driver, but due to the output voltage being close to its final value, a
much shorter power-up delay time setting can be used and still avoid any audible output artifacts. These output
voltage options are controlled in Page-0/Reg-42.
The high power output drivers can also be programmed to power up first with the output level control in a highly
attenuated state, then the output driver will automatically slowly reduce the output attenuation to reach the
desired output level setting programmed. This capability is enabled by default but can be enabled in
Page-0/Reg-40.
The TLV320AIC33 includes programmable short-circuit protection for the high power output drivers, for maximum
flexibility in a given application. By default, if these output drivers are shorted, they will automatically limit the
maximum amount of current that can be sourced to or sunk from a load, thereby protecting the device from an
over-current condition. In this mode, the user can read Page-0/Reg-95 to determine whether the part is in
short-circuit protection or not, and then decide whether to program the device to power down the output drivers.
However, the device includes further capability to automatically power down an output driver whenever it does
into short-circuit protection, without requiring intervention from the user. In this case, the output driver will stay in
a power down condition until the user specifically programs it to power down and then power back up again, to
clear the short-circuit flag.
The TLV320AIC33 includes extensive capability to monitor a headphone, microphone, or headset jack,
determine if a plug has been inserted into the jack, and then determine what type of headset/headphone is wired
to the plug. Figure 36 shows one configuration of the device that enables detection and determination of headset
type when a pseudo-differential (capless) stereo headphone output configuration is used. The registers used for
this function are Page-0/Reg 14, 37, 38, and 13. The type of headset detected can be read back from
Page-0/Reg-13. Note that for best results, it is recommended to select a MICBIAS value as high as possible, and
to program the output driver common-mode level at a 1.35V or 1.5V level.
42
Copyright 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): TLV320AIC33
相關PDF資料
PDF描述
TLV320AIC33IRGZ SPECIALTY CONSUMER CIRCUIT, PQCC48
TLV320AIC36IZQER SPECIALTY CONSUMER CIRCUIT, PBGA80
TLV320AIC36IZQE SPECIALTY CONSUMER CIRCUIT, PBGA80
TLV320DAC23IPW SERIAL INPUT LOADING, 32-BIT DAC, PDSO28
TLV320DAC23IGQER SERIAL INPUT LOADING, 32-BIT DAC, PBGA80
相關代理商/技術參數
參數描述
TLV320AIC33IZQE 功能描述:接口—CODEC Lo-Pwr Stereo Codec w/6 Inp 7 Otp RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
TLV320AIC33IZQE 制造商:Texas Instruments 功能描述:AUDIO CODEC IC ((NW))
TLV320AIC33IZQER 功能描述:接口—CODEC Lo-Pwr Stereo Codec w/6 Inp 7 Otp RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
TLV320AIC33NIZQE 制造商:Texas Instruments 功能描述:
TLV320AIC33NIZQER 制造商:Texas Instruments 功能描述:
主站蜘蛛池模板: 亳州市| 永济市| 西乌珠穆沁旗| 嫩江县| 台安县| 武宣县| 静乐县| 拉萨市| 蒲城县| 吉水县| 青田县| 眉山市| 韶关市| 天等县| 二连浩特市| 南雄市| 舞钢市| 盐边县| 台中市| 都昌县| 阿克陶县| 五华县| 三门县| 龙门县| 锦屏县| 贵溪市| 万州区| 迁西县| 盐城市| 许昌市| 呼和浩特市| 清远市| 青岛市| 神池县| 长宁区| 麻江县| 邵东县| 临城县| 南溪县| 武鸣县| 准格尔旗|